Кэнон 1133 ошибка е355 0005

Framin

  

Испачкался тонером

• 

• Canon G1010 series, G2010 series, G3010 series, G4010 series

  Verter в форуме Файлообменник

  0

  3579

  
  Verter
  
  Ср авг 19, 2020 12:00 pm
  

• Canon IR 2018 выдает ошибку «out of toner change toner»

  Sveterkom в форуме Принтеры, МФУ, копиры формата A3

  11

  10026

  
  Goldwater
  
  Чт окт 08, 2020 11:29 pm
  

• Canon G1000 series, G2000 series, G3000 series Service Manua

  Verter в форуме Файлообменник

  10

  5882

  
  Azelus
  
  Пт июн 12, 2020 4:46 am
  

• Canon IR 3225 «засыпает»

  johnnybravo в форуме Принтеры, МФУ, копиры формата A3

  4

  7167

  
  johnnybravo
  
  Пн июл 23, 2012 1:32 pm
  

• Canon mf3010 сразу мигает «о»

  Sveterkom в форуме Принтеры, МФУ, факсы, копиры формата A4

  2

  2037

  
  Сергей Владимиров
  
  Пт янв 21, 2022 2:04 pm
  

Thanks:  0

Likes:  0

Dislikes:  0

1. 02-19-2013

   
   

   #1

   

   
   Trusted Tech
   

   50+ Posts

   

   ---

   Rep Power

   24

   Canon ir1133if — E355
   

   IR1133IF — display is upside down with japanese writing and showing error E355. Unable to enter service mode or any other mode.

   Any ideas?

   ---

2. 02-19-2013

   
   

   #2

   Re: Canon ir1133if — E355
   

   Originally Posted by dickiebob
   

   IR1133IF — display is upside down with japanese writing and showing error E355. Unable to enter service mode or any other mode.

   Any ideas?

   Hi to every one,

   E355 Error code: When turning ON the power, inconsistency among the Serial N� PCB, the controller PCB (SRAM) and the counter the counter memory PCB is detected.

   I am not sure of the following: If your machine is networked, use its IP address to enter the Remote Unite Interface and choose the displaying language.

   Rachid.

   «Find a job you love and you�ll never have to work a day in your life.» Nagy’s father

   ---

3. 02-19-2013

   
   

   #3

   Re: Canon ir1133if — E355
   

   Originally Posted by dickiebob
   

   IR1133IF — display is upside down with japanese writing and showing error E355. Unable to enter service mode or any other mode.

   Any ideas?

   Hello again,

   The fact of not being able to enter neither the service mode, nor the user mode is a consequence of the E355 error code.

   Rachid.

   «Find a job you love and you�ll never have to work a day in your life.» Nagy’s father

   ---

4. 02-19-2013

   
   

   #4

   Re: Canon ir1133if — E355
   

   Originally Posted by dickiebob
   

   IR1133IF — display is upside down with japanese writing and showing error E355. Unable to enter service mode or any other mode.

   Any ideas?

   MNCON clear may resolve the Japanese issue.
   or re-install the System Software.

   like this in English version
   

   Try Refitting all the harness connections within the control panel assembly

   E355 is another issue

   E355 error may appear after replacing the Counter Memory PCB

   what did u do before ERROR ??
   were u swapping pcb’s
   Japanese ??? what was it before ??

   don’t know or think if your model supports this below
   To clear an E355 code, access Level 3 of Service Mode. This can be done by following the procedures below.
   — Press «*«, then Press «2» and «8» simultaneously, then Press «*«
   — Press » * «, then Press «1» and «9» simultaneously, then Press «3«
   — Press Copier / Function / Clear / E355 , then Press OK and then Press Reset
   — Turn the machine off, then on using the main switch which is located below and to the rear of the bypass tray.

   DO NOT MAKE ANY CHANGES IN LEVEL 3 SERVICE MODE. Only used for the E355 clear. Any adverse affects on the machine will not be supported by Canon USA if Level 3 service modes are adjusted.

   or

   maybe this———————
   

   Procedure for Clearing the Code:1. Enter the Service Mode — Additional Function — then hit the # Key
   2. Scroll(arrow)to #12 Clear — then hit the Set Key3.Scroll (arrow)to ERR — then hit the Set Key4. E355-CLR will be displayed — then hit the Set Key to clear the E355
   5. OK should display — then the machine will return to the Standby Screen
   
   —————————————————————————————
   or

   E355

   error code is due to no communication between the Main-Controller board and the Serial Number board below it. The boards are connected by a 11 PIN yellow connector and cable. This yellow connector must be reseated on the new Main-Controller board when changed. The connector must be seated firmly on the board.

   1. Enter Service Mode: Press * Additional Functions, 2&8 simultaneously, then * Additional Functions again.
   2. Then select the [COPIER] option. Under [COPIER], select the Function tab.
   3. Under the [FUNCTION] tab, select the [CLEAR] option.
   4. In [CLEAR] there is a selection E355-CLR. Select it and hit OK.
   5. Reboot the machine.

   **Knowledge is time consuming, exhausting and costly for a trained Tech.**

   ---

5. 02-21-2013

   
   

   #5

   

   
   Trusted Tech
   

   50+ Posts

   

   ---

   Rep Power

   24

   Re: Canon ir1133if — E355
   

   Originally Posted by teckat
   

   MNCON clear may resolve the Japanese issue.

   or re-install the System Software.

   like this in English version
   

   Try Refitting all the harness connections within the control panel assembly

   E355 is another issue

   E355 error may appear after replacing the Counter Memory PCB

   what did u do before ERROR ??
   were u swapping pcb’s
   Japanese ??? what was it before ??

   don’t know or think if your model supports this below

   To clear an E355 code, access Level 3 of Service Mode. This can be done by following the procedures below.
   — Press «*«, then Press «2» and «8» simultaneously, then Press «*«
   — Press » * «, then Press «1» and «9» simultaneously, then Press «3«
   — Press Copier / Function / Clear / E355 , then Press OK and then Press Reset
   — Turn the machine off, then on using the main switch which is located below and to the rear of the bypass tray.

   DO NOT MAKE ANY CHANGES IN LEVEL 3 SERVICE MODE. Only used for the E355 clear. Any adverse affects on the machine will not be supported by Canon USA if Level 3 service modes are adjusted.

   or

   maybe this———————
   

   Procedure for Clearing the Code:

   1. Enter the Service Mode — Additional Function — then hit the # Key
   2. Scroll(arrow)to #12 Clear — then hit the Set Key

   3.Scroll (arrow)to ERR — then hit the Set Key

   4. E355-CLR will be displayed — then hit the Set Key to clear the E355
   5. OK should display — then the machine will return to the Standby Screen
   
   —————————————————————————————
   or

   E355

   error code is due to no communication between the Main-Controller board and the Serial Number board below it. The boards are connected by a 11 PIN yellow connector and cable. This yellow connector must be reseated on the new Main-Controller board when changed. The connector must be seated firmly on the board.

   1. Enter Service Mode: Press * Additional Functions, 2&8 simultaneously, then * Additional Functions again.
   2. Then select the [COPIER] option. Under [COPIER], select the Function tab.
   3. Under the [FUNCTION] tab, select the [CLEAR] option.
   4. In [CLEAR] there is a selection E355-CLR. Select it and hit OK.
   5. Reboot the machine.

   Thanks, but the machine does not let us get in to service mode. We have managed to get it back to an English display, but it is still upside down. None of the buttons on the control panel work. Machine has only done 5k.

   ---