005-131, 005-132 DADF Invert Sensor On Jam During Inverting RAP
BSD-ON: BSD 5.6 Document Scan, Invert and Exit Transportation
005-131 After the DADF registration sensor turned on at invert operation, the DADF invert sensor did not turn on within the specified time.
005-132 DADF invert sensor will not turn on after DADF registration sensor on in simplex.
Procedure
WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
Perform the steps that follow:
1. Check for a foreign substance in the document path.
2. Check the surface of the out roll for foreign substances or wear. Clean or install new components as necessary, PL 5.50.
3. Enter dC330, code 005-211. Check the DADF invert sensor, PL 5.50 Item 8.
4. Enter dC330, code 005-110. Check the DADF registration sensor, PL 5.70 Item 3.
5. Enter dC330, code 005-008. Check the DADF feed motor, PL 5.30 Item 3.
6. Check the drive gears, (W/OTAG 002, PL 5.35), (W/TAG 002, PL 5.36) for wear or damage. Install new components as necessary.
7. If the fault persists, install a new DADF PWB, PL 5.10 Item 11.
**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**
You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.
Toner Chip (For North America and West Europe Region):
• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738
Toner Chip (For South America and East Europe Region):
• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766
Toner Chip (For Metered Machine):
• 106R03733 106R03736 106R03735 106R03734
Drum Chip:
• 113R00780 113R00782
The most common error codes.
| Error | |
|---|---|
| 077-214 | Description: Tray Module Logic Fail RAP I/F mismatch between the IOT and the Tray Module was detected. |
| 005-940 | Description: DADF No Original RAP Operation Fail. Final document correction notification due to DADF document being pulled out. |
| 012-212 | Description: Stacker Tray Upper Limit Failure RAP (LX) The stacker has continued to elevate after the defined period of time has passed since Stacker No Paper Sensor is ON during stacker elevation. |
| 012-291 | Description: (Integrated Finisher) Stapler Fail RAP Within a specified time after the Staple Motor started rotating in reverse direction, the Staple Head Home Sensor was never detected turning On. |
| 092-315 | Description: ATC Fail RAP The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring has exceeded the threshold value. NOTE: • Although this Fault can be cleared by turning the power OFF and ON and it will be possible to out |
| 012-291 | Description: (Integrated Finisher) Stapler Fail RAP Within a specified time after the Staple Motor started rotating in reverse direction, the Staple Head Home Sensor was never detected turning On. |
| 062-396 | Description: CCD Cable Connection Fail RAP A CCD Flat Cable connection error was detected. |
| 077-214 | Description: Tray Module Logic Fail RAP I/F mismatch between the IOT and the Tray Module was detected. |
| 041-310 | Description: IM Logic Fail RAP The IM (Image Management) software control error was detected. |
| 005-940 | Description: DADF No Original RAP Operation Fail. Final document correction notification due to DADF document being pulled out. |
Xerox Error Code Database – With Answers
Hello Hello!
If you have found yourself here, you are probably looking for what one of these error codes means. We have complied the entire list of all the Xerox Error Code here.
This database is ever evolving. Each time we find a solution to one of these error codes, we will write another entry on it and put a link to the code here.
March 2019 Update-
Found this website helping another customer. This has older models with error code searchable –
https://printcopy.info/?l=en&mod=erc&brand=Xerox&page=1
Quickly Jump to a Xerox Error Code
To quickly jump to the code in which the internet brought you here, Hold down CTRL + F , on the keyboard. This will pull up the search window. Type in the code and the screen will shift to that code.
002-770 RAP Insufficient HDD capacity while processing the job template within a job.
03-318 RAP IIT software failure.
03-319 RAP IIT Video Driver Detection Fail. 003-320 RAP IIT-ESS Communication Fail 1.
03-321 RAP IIT-ESS Communication Fail 2.
03-322 RAP IIT-ESS Communication Fail 3.
03-323 RAP IIT-ESS Communication Fail 4.
03-324 RAP IIT-ESS Communication Fail 5.
03-325 RAP IIT-ESS Communication Fail 6.
03-326 RAP IIT-ESS Communication Fail 7.
03-327 RAP IIT-ESS Communication Fail 8.
03-328 RAP IIT-ESS Communication Fail 9.
03-329 RAP IIT-ESS Communication Fail 10.
03-330 RAP IIT-ESS Communication Fail 11.
03-331 RAP IIT-ESS Communication Fail 12.
03-332 RAP IIT-ESS Communication Fail 13.
03-333 RAP IIT-ESS Communication Fail 14.
03-334 RAP IIT-ESS Communication Fail 15.
03-335 RAP IIT-ESS Communication Fail 16.
03-336 RAP IIT-ESS Communication Fail 17.
03-337 RAP IIT-ESS Communication Fail 18.
03-338 RAP IIT-ESS Communication Fail 19.
03-339 RAP IIT-ESS Communication Fail 20.
03-340 RAP IIT-ESS Communication Fail 21.
03-341 RAP IIT-ESS Communication Fail 22.
03-342 RAP IIT-ESS Communication Fail 23.
03-343 RAP IIT-ESS Communication Fail 24.
003-344 RAP Power on hotline failure.
003-345 RAP X PIO Unmatch Fail 1.
003-346 RAP X PIO Unmatch Fail 2.
003-750 RAP Book Duplex-Insufficient Docs.
003-751 RAP Under PANTHER Capacity (Scan).
003-752 RAP This status code is displayed if 600dpi cannot be scanned (DADF).
003-753 RAP This status code is displayed if over 300dpi cannot be scanned (DADF).
003-754 RAP S2X Recoverable Error.
003-755 RAP S2X Command Error.
003-757 RAP This status code is displayed if over 400dpi cannot be scanned (DADF).
003-760 RAP Scan Settings Error.
003-761 RAP Incorrect Paper Tray Size.
003-763 RAP Adjustment Chart Not Found.
003-764 RAP Adjustment Chart Not Found.
003-780 RAP Scan Image Compression Error.
003-795 RAP AMS Limit Error.
003-940 RAP DAM Memory is insufficient.
003-942 RAP Document Size Error.
003-944 RAP Image Repeat Count Fail.
003-946 RAP Copy Vertical/Horizontal Difference (APS).
003-947 RAP Replaced Original Count Error.
003-948 RAP Replaced Original Mismatch.
003-952 RAP Return Documents Color mismatch.
003-955 RAP Documents Size Exchange Error.
003-956 RAP Documents Size Unknown Error.
003-963 RAP No APS Object Tray.
003-965 RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.
003-966 RAP AATS/APS No Destination Error.
003-968 RAP Punch Position Error.
003-969 RAP Punch Size Error.
003-972 RAP Maximum Stored Page Over Flow.
003-973 RAP Every Direction Difference.
003-974 RAP Next Original Specification.
003-977 RAP Document Miss Match (Multi Scan).
003-978 RAP Color Document Mismatch (Multi Scan). 003-980 RAP Staple Position Error.
003-981 RAP Staple Size Error.
003-982 RAP IITsc HDD Access Error.
005-121 RAP DADF Feed Sensor ON Jam.
005-122 RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam.
005-123 RAP DADF Simplex/Side 1 Reg Sensor ON Jam.
005-124 RAP DADF Lead Reg Sensor ON Jam.
005-125 RAP DADF Reg Sensor OFF Jam.
005-126 RAP DADF Out Sensor ON Jam.
005-127 RAP DADF Out Sensor OFF Jam.
005-128 RAP DADF Exit Sensor 1 ON Jam (Simplex Mode).
005-129 RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode).
005-130 RAP DADF Invert Sensor ON Jam (Duplex Mode).
005-131 RAP DADF Invert Sensor On Jam (Inverting).
005-132 RAP DADF Invert SNR on Jam 2.
005-133 RAP DADF Invert Sensor OFF Jam.
005-134 RAP DADF Invert SNR off Jam (Inv).
005-135 RAP DADF Pre Reg Sensor ON Jam (Invert).
005-136 RAP DADF Reg Sensor ON Jam (Invert).
005-137 RAP DADF Exit Sensor 2 ON Jam.
005-138 RAP DADF Exit Sensor 1 ON Jam.
005-139 RAP DADF Invert SNR off Jam.
05-141 RAP DADF Feed Sensor OFF Jam.
05-142 RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode).
005-143 RAP DADF Exit Sensor 2 OFF Jam.
005-144 RAP DADF Too First Pre Reg Sensor ON Jam.
005-145 RAP DADF Reg Sensor Off Jam (Invert).
05-146 RAP DADF Pre Reg Sensor Off Jam.
05-147 RAP DADF Pre Reg Sensor Off Jam (Invert).
005-150 RAP DADF Feed Sensor OFF Jam (Perforated Original Mode).
005-151 RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode).
005-152 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).
005-153 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).
005-154 RAP DADF Out Sensor OFF Jam (Perforated Original Mode).
005-155 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex).
05-156 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex).
05-157 RAP DADF Invert Sensor OFF Jam (Perforated Original Mode).
005-158 RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode).
005-160 RAP DADF Tray Lift Up Fail (Document Set) (Within Job).
005-190 RAP DADF Feed Motor Logic Jam.
005-194 RAP Size Mismatch Jam on Slow Scan Mix Size.
005-195 RAP Size Mismatch Jam on No Mix Size.
005-196 RAP Size Mismatch Jam on No Mix Size.
005-197 RAP Prohibit Combine Size Jam.
005-198 RAP Too Short Size Jam.
005-199 RAP Too Long Size Jam.
005-275 RAP DADF RAM Fail.
005-280 RAP DADF EEPROM Fail.
05-282 RAP DADF Tray Lift Up Fail (No Document).
05-283 RAP DADF Stack Height Sensor Logic Fail.
005-284 RAP DADF APS Sensor Logic Fail.
005-285 RAP DADF Nudger Lift Up Fail.
005-286 RAP DADF Feed Out Sensor Fail.
005-303 RAP DADF Tray Interlock is open.
005-304 RAP Platen Interlock Open.
005-305 RAP DADF Feeder Cover Interlock Open (Run).
005-306 RAP DADF Tray Interlock Open (Run).
005-308 RAP The DADF L/H Cover Interlock is open.
005-309 RAP DADF L/H Cover Interlock Open (Run).
005-906 RAP DADF Feed Sensor Static Jam.
005-907 RAP DADF Pre Reg Sensor Static Jam.
005-908 RAP DADF Reg Sensor Static Jam.
005-909 RAP DADF Lead Reg Sensor Static Jam..
005-910 RAP DADF Out Sensor Static Jam.
005-911 RAP DADF Exit Sensor 1 Static Jam.
005-912 RAP DADF Exit Sensor 2 Static Jam.
005-913 RAP DADF Invert Sensor Static Jam.
005-914 RAP DADF No. 1/2/3 APS Sensor Static Jam.
005-915 RAP DADF No. 1 APS Sensor Static Jam.
005-916 RAP DADF No. 2 APS Sensor Static Jam.
005-917 RAP DADF No. 3 APS Sensor Static Jam.
005-918 RAP DADF Invert Sensor 2 Static Jam.
005-919 RAP DADF Tray Lift Up Fail (Document Set).
005-940 RAP DADF No Original Fail.
005-941 RAP DADF Not Enough Document.
005-942 RAP DADF Tray Stack Over Fail.
010-311 RAP Fuser Heat Roll STS-1 Disconnection Fail. It was detected that fuser heat roll STS-1 disconnected.
010-319 RAP Fuser NC Sensor Differential Amp Fail.
010-320 RAP Heat Roll Over Heat Fail.
10-321 RAP Fuser Nip Fail.
10-322 RAP Fuser NC Center Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).
10-323 RAP Fuser Rear Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).
10-324 RAP Fuser NVM Fail.
010-326 RAP Wait Heat Roll Fuser On Time Fail.
010-327 RAP Standby Heat Roll Fuser On Time Fail.
010-330 RAP Fuser Motor Fail.
010-420 RAP Fuser Assembly Life Near End.
010-421 RAP Fuser Assembly Life End.
012-112 RAP Finisher Interface Entrance Sensor ON.
012-113 RAP Booklet In Sensor ON Jam.
12-114 RAP Booklet In Sensor OFF Jam.
12-115 RAP Booklet Folder Roll Exit Sensor ON Jam.
012-125 RAP Gate Sensor ON JAM: Finisher.
012-132 RAP Finisher Transport Entrance Sensor ON Jam (Long).
012-142 RAP Buffer Path Sensor ON Jam A.
012-151 RAP Compile Exit Sensor OFF Jam.
012-152 RAP Compile Exit Sensor ON Jam A.
012-161 RAP Set Eject Jam.
012-162 RAP Finisher Interface EXIT. Sensor ON Jam.
012-171 RAP Top Tray Exit Sensor ON Jam A.
012-172 RAP Top Tray Exit Sensor OFF Jam A.
012-180 RAP Booklet Folder Roll Exit Sensor OFF Jam.
012-211 RAP Stacker Tray Fail.
012-212 RAP Stacker Tray Upper Limit Fail.
012-213 RAP Stacker Tray Lower Limit Fail.
012-221 RAP Tamper Home Sensor ON Fail.
012-223 RAP Tamper Home Sensor OFF Fail.
012-224 RAP Rear Tamper Home Sensor OFF Fail.
012-225 RAP Booklet Tamper F Home Sensor ON Fail.
012-226 RAP Booklet Tamper F Home Sensor OFF Fail.
012-227 RAP Booklet End Guide Home Sensor OFF Fail.
012-228 RAP Booklet End Guide Home Sensor ON Fail.
012-229 RAP Booklet Tamper R Home Sensor ON Fail.
012-230 RAP Booklet Tamper R Home Sensor OFF Fail.
012-243 RAP Booklet Knife Home Sensor ON Fail.
12-246 RAP Booklet Stapler Fail.
12-247 RAP Side Regi Sensor OFF Fail.
012-260 RAP Eject Clamp Up Sensor ON Fail.
012-261 RAP Booklet Knife Folding SNR Fail.
012-263 RAP Finisher Rear Tamper Home Sensor ON.
012-264 RAP Booklet Drawer Broken Fail.
012-265 RAP Booklet Knife Home Sensor OFF Fail.
012-266 RAP Booklet Compiler No Paper Sensor Fail.
012-270 RAP Top Offset Home Sensor ON Fail: Finisher.
012-271 RAP Top Offset Home Sensor OFF Fail: Finisher.
012-282 RAP Eject Clamp Up Sensor OFF Fail.
012-283 RAP Finisher Set Clamp Home Sensor ON Fail.
012-284 RAP Finisher Set Clamp Home Sensor OFF Fail.
012-291 RAP Stapler Fail.
012-295 RAP Finisher Stapler Move Sensor On Fail.
012-296 RAP Finisher Stapler Move Sensor OFF Fail.
012-300 RAP Finisher Eject Cover Open (Compiler Cover).
012-302 RAP Finisher Front Door Interlock Open.
012-307 RAP Booklet Drawer Set Fail.
012-320 RAP Punch Home Sensor ON Fail.
12-321 RAP Punch Home Sensor OFF Fail.
12-322 RAP Puncher Move Home Sensor OFF Fail.
012-323 RAP Puncher Move Home Sensor On Fail.
012-325 RAP Side Regi Home Sensor On Fail.
012-330 RAP Decurler Cam Home Sensor OFF Fail.
012-332 RAP Decurler Cam Home Sensor ON Fail.
012-334 RAP Download Mode Fail.
012-335 RAP Booklet Sub CPU Communication Fail.
012-900 RAP Buffer Path Sensor Static Jam.
012-901 RAP Finisher Paper Remains at H-Transport Entrance.
012-902 RAP Finisher Paper Remains H-Transport Exit.
012-903 RAP Compile Exit Sensor Static Jam.
012-905 RAP Compile Tray No Paper Sensor Static Jam.
012-907 RAP Top Tray Exit Sensor Static Jam.
012-920 RAP Gate Sensor static JAM (to Top Tray) A: Finisher.
012-932 RAP Gate SNR static JAM (to Stacker Tray) A.
012-934 RAP Gate SNR static JAM (to Stacker Tray) C.
012-935 RAP Finisher Paper Remains at Transport Entrance Sensor.
012-936 RAP Paper Remain at Booklet In SNR A.
012-949 RAP Finisher Punch DustBox Miss Set.
013-902 RAP Booklet Compile No Paper Sensor Static Jam.
013-903 RAP Booklet Folder Roll Exit Sensor Static Jam.
16-210 RAP Software Option Fail (HDD Not Exist).
16-211 RAP Software Option Fail (System Memory Low Volume).
016-212 RAP SW Option Fail (Page Memory Low).
016-213 RAP SW Option Fail (Printer CARD Not Exist).
016-215 RAP SW Option Fail (JPEG Board Not Exist).
16-216 RAP SW Option Fail (Ext Memory Not Exist).
16-217 RAP SW Option Fail (Controller ROM not Printer kit).
16-218 RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.
16-219 RAP License is required (Printer Kit).
016-220 RAP S2X Unrecoverable Error.
016-221 RAP S2X Communication Error.
016-222 RAP S2X Self-Diag Error.
16-223 RAP SS2X SDRAM Error.
16-224 RAP S2X PCI Reg Error.
16-225 RAP S2X ROM CheckSum Error.
016-226 RAP S2X IIT Connection Error.
016-227 RAP S2X DDR Error.
16-228 RAP S2X Image Processing Error.
16-229 RAP SW Option Fail (FCW-UI Not Exist).
016-311 RAP The scanner was not detected.
16-315 RAP NIIT Interface Fail.
16-316 RAP Page Memory Not Detected.
016-317 RAP Page Memory Broken-Standard.
016-318 RAP Page Memory Broken-Option.
016-320 RAP A fatal error with doc conversion software was detected.
016-322 RAP JBA Account Full.
016-450 RAP SMB Host Name Duplicated.
016-454 RAP DNS Renewal Failure of Dynamic.
016-455 RAP SNTP Server Time Out.
016-456 RAP SNTP Time Asynchronous.
016-503 RAP SMTP Server Address Resolution Fail.
016-504 RAP POP Server Address Resolution Fail.
016-505 RAP POP Authentication Fail.
016-600 RAP KO Authentication Locked.
016-601 RAP Illegal Access Detection.
016-647 RAP With APS selected or with APS set up, there were no trays loaded with paper sizes for Auto Paper Selection.
016-648 RAP Job with Booklet selected was discontinued because it had a cover with an image, a divider, or a blank page.
016-701 RAP Out of ART EX Memory.
016-702 RAP Out of Page Buffer.
016-703 RAP Email to Invalid Box.
016-704 RAP Mailbox is Full.
016-705 RAP Secure Print Fail.
016-706 RAP Max. User Number Exceeded.
016-707 RAP Sample Print Fail.
016-708 RAP HD Full by Annotation/Watermark Image.
016-709 RAP ART EX Command Error.
016-710 RAP Delayed Print Fail.
016-711 RAP Tried to send data whose size is over the system data upper limit.
016-712 RAP Under PANTHER Capacity (I-Formatter).
016-713 RAP Security Box Password Error.
016-714 RAP Security Box is not Enabled.
016-716 RAP TIFF Data Overflow.
016-718 RAP Out of PCL6 Memory.
016-719 RAP Out of PCL Memory.
016-720 RAP PCL Command Error.
016-721 RAP Other Error.
016-722 RAP Job Cancel by Staple Position NG.
016-723 RAP Job Cancel by Punch Position NG.
016-724 RAP Complex Position Error of Staple and Punch.
016-726 RAP PDL Auto Switch Fail.
016-728 RAP Unsupported TIFF Data.
016-729 RAP TIFF Data Size too Big.
016-730 RAP Unsupported ART Command.
016-731 RAP Invalid TIFF Data.
016-732 RAP Form Not Registered.
016-733 RAP Destination Address Resolution Error.
016-734 RAP Simple Transmission report invocation error.
016-735 RAP Updating Job Template.
016-736 RAP Remote directory lock error. Lock directory creation failed.
016-737 RAP Remote lock directory remove error.
016-738 RAP PS Booklet Print Output Paper Size is illegal.
016-739 RAP Mismatch between PS Booklet Doc and Output Paper. 016-740 RAP PS Booklet Output Tray is incorrect.
016-746 RAP Unsupported PDF File.
016-748 RAP HD Full.
016-749 RAP JCL Syntax Error.
016-751 RAP PDF Error.
016-752 RAP PDF Short of Memory.
016-753 RAP PDF Password Mismatched.
016-754 RAP PDF LZW Not Installed.
016-755 RAP PDF Print Prohibited.
016-756 RAP Auditron-Prohibit Service.
016-757 RAP Auditron-Invalid User.
016-758 RAP Auditron-Disabled Function.
016-759 RAP Auditron-Reached Limit.
016-760 RAP PS Decompose Failure.
016-761 RAP FIFO Empty.
016-762 RAP Print LANG Not Installed.
016-764 RAP SMTP Server Connect Error.
016-765 RAP SMTP Server HD Full.
016-766 RAP SMTP Server File System Error.
016-767 RAP Invalid E-mail Address.
016-768 RAP Invalid Sender Address.
016-769 RAP SMTP Server Unsupported DSN.
016-771 RAP Scan Data Repository ERR.
016-772 RAP Scan Data Repository ERR.
016-773 RAP Invalid IP Address.
016-774 RAP HD Full-Compression Convert.
016-775 RAP HD Full-Image Convert.
016-776 RAP Image Convert ERR.
016-777 RAP HD Access ERR-Image Convert.
016-778 RAP HD Full-Scan Image Convert.
016-779 RAP Scan Image Conversion Error.
016-780 RAP HD Access ERR-Image Convert.
016-781 RAP Scan Server Connect ERR.
016-782 RAP Scan Server Login ERR.
016-783 RAP Invalid Server Path.
016-784 RAP Server Write ERR.
016-785 RAP Server HD Full.
016-786 RAP HD Full-Scan Write ERR.
016-787 RAP Invalid Server IP ADD.
016-788 RAP Retrieve to Browser Failed.
016-789 RAP HD Full-Job Memory.
016-791 RAP File Retrieve Fail.
016-792 RAP Specified Job Not Found.
016-793 RAP MF I/O HD Full.
016-794 RAP Media Reader: Media No Insert.
016-795 RAP Media Reader: Format Error.
016-796 RAP Document insert operation error.
016-797 RAP Media Reader: Image File Read Error.
016-798 RAP No Trust Marking Option.
016-799 RAP Print Instruction Fail.
RAP With Duplex Output selected, a size difference between side 1 and side 2 was detected.
RAP With Booklet selected, mixed-in-size/orientation pages with images were detected.
RAP After a duplexed page was deleted, a size difference between side 1 and side 2 was detected.
RAP After a document or divider was inserted, a size difference between side 1 and side 2 was detected.
RAP Documents were merged, including the cover with an image, or a document with a divider.
RAP A document unavailable for duplex print was inserted after a document available for Duplex was inserted.
RAP A document or a divider was inserted after the cover or divider page.
016-949 RAP The user inserted a documnet different in size/orientation from the page to be processed.
016-981 RAP A failure in access to HDD.
016-982 RAP HDD Access Error 2.
016-985 RAP Data Size Over Flow (Scan to Email).
024-340 RAP IOT-ESS Communication Failure 1.
24-341 RAP IOT-ESS Communication Failure 2.
24-342 RAP IOT-ESS Communication Failure 3.
24-343 RAP IOT-ESS Communication Failure 4.
24-345 RAP IOT-ESS Communication Failure 5.
24-346 RAP IOT-ESS Communication Failure 6.
24-347 RAP IOT-ESS Communication Failure 7.
24-348 RAP IOT-ESS Communication Failure 8.
24-349 RAP IOT-ESS Communication Failure 9.
24-350 RAP IOT-ESS Communication Failure 10.
24-351 RAP IOT-ESS Communication Failure 11.
24-352 RAP IOT-ESS Communication Failure 12.
24-353 RAP IOT-ESS Communication Failure 13.
24-354 RAP IOT-ESS Communication Failure 14.
24-355 RAP IOT-ESS Communication Failure 15.
24-356 RAP IOT-ESS Communication Failure 16.
24-357 RAP IOT-ESS Communication Failure 17.
24-358 RAP IOT-ESS Communication Failure 18.
24-359 RAP IOT-ESS Communication Failure 19.
024-360 RAP IOT-ESS Initialization Failure.
024-361 RAP Invalid IOT PaperSizeGroup Information.
024-362 RAP Page Sync Illegal Start.
24-363 RAP Page Sync Illegal Stop.
24-364 RAP DMA Transfer Failure.
24-365 RAP Overflow on the Loop Back Write.
024-366 RAP JBIG Library Other Failure.
024-367 RAP Decompress Other Failure.
024-368 RAP PCI Error.
24-370 RAP Marker Code Detect Failure.
24-371 RAP IOT-ESS Communication Failure 21.
24-372 RAP IOT-ESS Communication Failure 22.
24-373 RAP IOT-ESS Communication Failure 23.
024-374 RAP Regi Con PLL Parameter Failure.
024-375 RAP IOT-ESS Communication Failure 24.
024-600 RAP Billing master counter repair.
024-601 RAP Billing backup counter #1 repair.
024-602 RAP Billing backup counter #2 repair.
024-603 RAP SWKey master counter repair.
024-604 RAP SWKey backup counter #1 repair.
024-605 RAP SWKey backup counter #2 repair.
024-606 RAP Production Number/Serial Number Failure.
024-746 RAP Selected Paper Tray Parameter Mismatch.
024-747 RAP Print Instruction Failure.
RAP Tray 1 Size Mismatch.
RAP Tray 2 Size Mismatch.
RAP Tray 3 Size Mismatch.
RAP Tray 4 Size Mismatch.
RAP Tray 6 Size Mismatch.
RAP Tray 7 Size Mismatch.
024-917 RAP Stacker Tray Staple Set Over Count.
024-919 RAP Face UP Tray Close.
024-920 RAP Face Down Tray 1 Paper FULL.
024-922 RAP Face Down Tray 2 Paper FULL.
024-923 RAP Operation Yellow Toner Empty.
024-924 RAP Operation Magenta Toner Empty.
024-925 RAP Operation Cyan Toner Empty.
024-926 RAP Punch Dust Box Missing Set.
024-927 RAP Offset Catch Tray Full Stack.
024-930 RAP Stacker Tray Full (Small Size Full).
024-934 RAP Paper type mismatch.
024-935 RAP Tray 1 Paper Mismatch.
024-936 RAP Tray 2 Paper Mismatch.
024-937 RAP Tray 3 Paper Mismatch.
024-938 RAP OHP kind Mismatch at Tray 4 (Not White Frame OHP).
024-939 RAP Transparency type mismatch (No white border).
024-940 RAP Folder Tray Out of Place.
024-941 RAP Folder Tray Full Stack.
024-942 RAP Booklet Sheets Over Count.
024-943 RAP Booklet Low Staple.
024-945 RAP Booklet Full Stack.
024-946 RAP Tray 1 Not In Position.
024-947 RAP Tray 2 Not In Position.
024-948 RAP Tray 3 Not In Position.
024-949 RAP Tray 4 Not In Position.
024-950 RAP Tray 1 No Paper.
024-951 RAP Tray 2 No Paper.
024-952 RAP Tray 3 No Paper.
024-953 RAP Tray 4 No Paper.
024-954 RAP MSI No Paper.
024-955 RAP Tray 6 No Paper.
024-956 RAP Tray 7 No Paper.
024-957 RAP Interposer No Paper.
024-958 RAP MSI Size Mismatch.
024-959 RAP Tray 1 Paper Size Mismatch.
024-960 RAP Tray 2 Paper Size Mismatch.
024-961 RAP Tray 3 Paper Size Mismatch.
024-962 RAP Tray 4 Paper Size Mismatch.
024-965 RAP ATS/APS No Paper.
024-966 RAP ATS/APS No Destination Error.
024-967 RAP Different Width Mix Paper Detect (Staple Job).
024-968 RAP Stapler/Punch Batting.
024-969 RAP Different Width Mix Punch.
024-970 RAP Tray 6 Not In Position.
024-971 RAP Tray 7 Not In Position.
024-972 RAP Tray 6 Paper Size Mismatch.
024-973 RAP Tray 7 Paper Size Mismatch.
024-974 RAP Interposer Tray Size Mismatch.
024-975 RAP Booklet Sheets Over Count (Not Field Attachment).
024-976 RAP Finisher Staple Status incorrect.
024-977 RAP Stapler Feed Ready Failure.
024-978 RAP Booklet Stapler incorrect.
024-979 RAP Stapler Near Empty.
024-980 RAP Finisher Stacker Tray Full.
024-981 RAP Finisher Top Tray Full.
024-982 RAP Stacker Lower Safety Warning.
024-983 RAP Booklet Tray Full.
024-984 RAP Booklet Low Staple F.
024-985 RAP SMH Stop Check.
024-987 RAP Envelope Folder Tray Full.
024-988 RAP Envelope Folder Tray Set Failure.
024-989 RAP Booklet Low Staple R.
024-990 RAP Punch Dust Full.
025-596 RAP Diag HDD Failure 1.
025-597 RAP Diag HDD Failure 2.
027-452 RAP Duplicate IP address.
027-500 RAP SMTP Server Address Resolution Failure.
027-501 RAP POP Server Address Resolution Failure.
027-502 RAP POP Authentication Failure.
027-700 RAP Media Failure.
027-701 RAP Media Not Found.
027-702 RAP Media Data Not Found / Not Supported. 027-703 RAP Media Reader Failure / Disconnected.
027-706 RAP Certificate not found. 027-707 RAP Certificate expired.
027-708 RAP Certificate untrusted. 027-709 RAP Certificate revoked.
027-710 RAP S/MIME mail was disabled.
027-711 RAP S/MIME mail sender certificate not found. 027-712 RAP S/MIME mail sender certificate not valid. 027-713 RAP S/MIME mail was altered.
027-714 RAP S/MIME mail sender impersonation. 027-715 RAP S/MIME mail certificate not supported. 027-716 RAP No-Signed mail receipt was rejected.
027-720 RAP Ext Srv. Host Not Found. A server specified for a remote application was not found, or DNS resolution was not possible.
027-721 RAP Ext Srv. Not Found.
027-722 RAP Ext Srv. Timeout Failure.
027-723 RAP Ext Srv. Authentication Failure. 027-724 RAP Ext Srv. Access Failure.
027-725 RAP Ext Srv. Operation Failure. 027-726 RAP Ext Srv. Unknown State.
027-727 RAP Ext Srv. Req Invalid Parameters. 027-728 RAP Ext Srv. Required File Exceeded.
027-737 RAP Template Server Read Error. 027-739 RAP Invalid Template Server Path. 027-740 RAP Template Server Login Error.
027-741 RAP Template Server Connect Failure. 027-742 RAP HD File System Full.
027-743 RAP Template Server Install Error. 027-744 RAP Template Server ADD Error.
027-745 RAP Template Server ADD Error.
027-746 RAP Job Template Pool Server Not Ready. 027-751 RAP Job Template Analysis Error.
027-752 RAP Must User un Inputting.
027-753 RAP Job Flow Service Request Disabled. 027-760 RAP XJT Command Failure.
027-770 RAP PDL Error.
027-771 RAP DFE Disk Full.
027-796 RAP Email Not Printed.
027-797 RAP Invalid Output Destination. 042-313 RAP Rear Cooling Fan Failure.
042-320 RAP Yellow Drum Motor Drive Failure. 042-321 RAP Magenta Drum Motor Drive Failure. 042-322 RAP Cyan Drum Motor Drive Failure.
042-323 RAP Black Drum Motor Drive Failure. 042-324 RAP IBT Drive Motor Failure.
42-325 RAP Main Motor Failure.
42-326 RAP Belt Home Position too long. 042-327 RAP Belt Position Failure.
042-328 RAP Belt Edge Sensor Failure. 042-330 RAP Fuser Exhaust Fan Failure. 042-331 RAP Blower Motor Fan Failure. 042-600 RAP Belt Walk Failure.
042-601 RAP Belt Edge Learn Failure. 042-602 RAP Belt Edge Check Failure.
042-603 RAP Suction Filter Life End Failure. 045-310 RAP Image Ready NG.
045-311 RAP Controller Comm Failure. 045-312 RAP Driver Connect Failure.
047-210 RAP OCT Offset Failure.
047-310 RAP MCU-Finisher Communication Failure. 061-310 RAP Clapper 1 Failure.
061-311 RAP Clapper 2 Failure.
061-313 RAP SOS Long Failure Magenta. 061-315 RAP SOS Long Failure Black.
061-317 RAP SOS Short Failure.
061-319 RAP SOS Short Failure Black. 061-320 RAP Polygon Motor Failure.
061-321 RAP ROS Motor Failure. 061-323 RAP No SOS Failure.
061-324 RAP No SOS Failure. 061-325 RAP No SOS Failure.
061-326 RAP ROS Connect Failure Yellow. 061-327 RAP ROS Connect Failure.
61-328 RAP ROS Connect Failure.
61-329 RAP ROS Connect Failure Black. 061-334 RAP ROS Y/M VDD Failure.
61-335 RAP ROS C/K VDD Failure.
61-336 RAP ROS Y/M VDD Down Failure.
61-337 RAP ROS C/K VDD Down Failure. 061-338 RAP SOS Stop Magenta Failure. 061-339 RAP SOS Stop Black Failure.
061-340 RAP ROS LD Failure Black. 061-341 RAP ROS LD Failure Yellow. 061-342 RAP ROS LD Failure Magenta. 061-343 RAP ROS LD Failure Cyan.
061-600 RAP ROS Data Failure Yellow. 061-601 RAP ROS Data Failure Magenta. 061-602 RAP ROS Data Failure Cyan.
061-603 RAP ROS Data Failure Black. 061-604 RAP LD Alarm Yellow.
061-605 RAP LD Alarm Magenta. 061-606 RAP LD Alarm Cyan.
061-607 RAP LD Alarm Black.
62-210 RAP IISS Hot Line Failure.
62-211 RAP IIT/IPS EEPROM Failure (IPS).
062-220 RAP IPS-EXT Connection Failure.
062-277 RAP IIT/IPS-DADF Communication Failure. 062-278 RAP IIT-Extension Communication Failure. 062-300 RAP Platen Interlock Open.
062-310 RAP IIT/IPS-ESS Communication Failure. 062-311 RAP IIT Software Logic Failure.
62-321 RAP IPS-YATA Connection Failure.
62-322 RAP EXT-YATA Connection Failure. 062-323 RAP YATA PWBA Failure.
062-345 RAP IIT/IPS EEPROM Failure (IIT).
062-355 RAP IPS Fan Failure. 062-356 RAP Lamp Fan Failure.
062-357 RAP CCD Fan Failure. An error signal was detected for the CCD fan.
062-360 RAP Carriage Position Failure. 062-362 RAP X Hard Failure.
062-371 RAP Lamp Failure.
062-380 RAP Platen AOC Failure. 062-386 RAP Platen AOC Failure.
062-389 RAP Carriage Over Run (Scan End). 062-392 RAP IT/IPS Memory Failure.
062-393 RAP IIT/IPS PWB Failure.
062-790 RAP X Detect Failure.
063-210 RAP Extension EEPROM Failure. 063-220 RAP IPS-EXT Psync Failure.
063-230 RAP EXT Image Parameter Failure. 063-240 RAP EXT Image Parameter Failure. 065-210 RAP Extension Page Memory Failure 1. 065-211 RAP CIS Shading FROM Failure
065-212 RAP CIS Shading Level Failure. 065-213 RAP CIS Output Level Failure.
065-215 RAP Extension Page Memory Failure 2. 065-216 RAP Extension Page Memory Failure 3. 065-219 RAP CIS Black White Level Failure.
065-220 RAP 1P DUP PWB-EXT Psync Failure.
071-101 RAP Feed Out Sensor 1 is not turned ON.
071-104 RAP Pre Registration Sensor ON Jam (Tray 1). 071-105 RAP Registration Sensor ON Jam (Tray 1).
071-210 RAP Tray 1 Lift Up Failure. 072-101 RAP Tray 2 Miss Feed Jam.
072-102 RAP The Tray 1 Feed Out Sensor does not turn ON. 072-104 RAP Pre-Registration Sensor ON Jam (Tray 2).
072-105 RAP Registration Sensor ON Jam (Tray 2). 072-210 RAP Tray 2 Lift Up Failure.
73-101 RAP Tray 3 Miss Feed Jam.
73-102 RAP Feed Out Sensor 1 ON Jam (Tray 3).
73-104 RAP Pre Registration Sensor ON Jam (Tray 3).
73-105 RAP Registration Sensor ON Jam (Tray 3). 073-210 RAP Tray 3 Lift Up Failure.
74-101 RAP Pre Feed Sensor 4 is not ON within the specified time after the start of feed from Tray 4.
74-102 RAP Feed Out Sensor 1 ON Jam (Tray 4).
74-103 RAP The Tray 4 Feed Out Sensor is not ON within the specified time for paper fed from Tray 4.
74-104 RAP Pre Registration Sensor ON Jam (Tray 4). 074-105 RAP Registration Sensor ON Jam (Tray 4).
074-210 RAP Tray 4 Lift Up Failure.
75-100 RAP Tray 5/Bypass Pre Feed Sensor is not ON within the specified time after the start of feed from Tray 5.
75-101 RAP Tray 5/Bypass Feed Out Sensor is not ON within the specified time for paper fed from Tray 5.
075-109 RAP Paper from Tray 5/Bypass does not turn ON Pre Regi Sensor within a specified time.
075-135 RAP Paper from Tray 5/Bypass does not turn ON Regi Sensor within a specified time.
75-210 RAP Tray 5/Bypass Lift Up Sensor does not turn ON within a specified time after Tray 5 begins to lift.
75-211 RAP Tray 5/Bypass Lift Down Sensor does not turn ON within a specified time after Tray 5 begins to lower.
77-102 RAP Paper from Tray 2 did not turn on the Transport Path Sensor 1 within the specified time.
77-103 RAP The Fuser Exit Sensor did not turn off within the specified time in straight exit mode.
77-106 RAP The Fuser Exit Sensor did not come on within the specified time after the Registration Motor.
77-107 RAP The Fuser Exit Sensor did not turn off within the specified time in invert exit mode.
077-109 RAP The IOT Exit Sensor did not come on at the specified time in non-invert mode.
077-111 RAP The IOT Exit Sensor did not come on within the specified time in invert exit mode.
077-113 RAP The IOT Exit Sensor did not turn off at the specified time in non-invert mode.
077-115 RAP The IOT Exit Sensor did not turn off within the specified time in invert exit mode.
077-118 RAP Paper from Duplex did not turn on the Pre Regi Sensor within the specified time.
077-120 RAP Post 2nd BTR Sensor On JAM.
077-123 RAP Duplex In Sensor does not turn ON a spec time after the start of invert.
77-129 RAP Paper from Duplex did not turn on the Regi Sensor within the specified time.
77-130 RAP Duplex Out Sensor does not turn ON witin a specified time after Duplex In Sensor turns ON.
77-300 RAP The Front Cover is open.
77-301 RAP The Left Hand Interlock is open.
77-302 RAP The Right Hand Cover Interlock is open. 077-303 RAP PH Drawer Interlock Open.
077-304 RAP The Tray 5/Bypass Cover Interlock is open. 077-312 RAP Feeder Communication Failure.
077-909 RAP One of the IOT sensors detected paper when power was turned on or when an interlock was closed.
077-967 RAP The specified paper type and the paper type being used are different.
077-968 RAP The type of paper in the tray was changed.
78-100 RAP Paper from Tray 6 does not turn ON Pre Regi Sensor within a specified time.
78-101 RAP The Tray 6 Feed Out sensor is not ON within the specified time for paper fed from Tray 6.
78-102 RAP Paper from Tray 6 does not turn ON the Regi Sensor within a specified time.
078-151 RAP The Tray 6 Feed Out Sensor did not come on within the specified time after the start of feed.
078-250 RAP HCF Tray #2 Lift Up Fail.
078-300 RAP The HCF transport interlock is open. 078-301 RAP HCF Side Out Interlock Open.
089-600 RAP Incorrect Fast Scan positioning for the reference color Cyan was detected during fine adjustment.
089-601 RAP The Inner MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-602 RAP The CENTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-603 RAP The OUTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-604 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-605 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-606 RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-607 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns correctly during Magenta rough adjustment.
089-608 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.
089-609 RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.
089-610 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-611 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-612 RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-613 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-614 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-615 RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-616 RAP RC Data OverFlow Failure.
089-617 RAP RC Data OverRange Failure.
91-311 RAP The voltage level of the CC cleaner position sensor did not change within the specified time.
91-312 RAP Charge (K) Preclean HVPS has failed.
91-313 RAP DRUM CRUM ASIC Communication Failure.
091-320 RAP Charge Corotron Wire is broken.
91-400 RAP The replacement date for Waste Toner Bottle (regular) is near.
91-401 RAP The black drum cartridge is near the end-of-life.
091-403 RAP The CC Assembly is near the end-of-life.
091-404 RAP The CC Assembly has reached the end-of-life.
091-411 RAP The yellow drum cartridge is near the end-of-life.
091-421 RAP The magenta drum cartridge is near the end-of-life.
091-431 RAP The cyan drum cartridge is near the end-of-life.
091-910 RAP The waste toner bottle is not present.
091-911 RAP The waste toner bottle is full.
091-913 RAP The black drum cartridge (K) has reached the end-of-life.
091-914 RAP Communication failure between the MCU and the black Drum CRUM.
091-915 RAP The MCU detected incorrect data in the black drum cartridge CRUM.
091-916 RAP The CRUM authentication registration data on the drum cartridge is incorrect.
091-917 RAP MCU cannot communicate with the CRUM in drum Y.
091-918 RAP Communication failure with the magenta Drum CRUM.
091-919 RAP Communication failure with the cyan Drum CRUM.
091-920 RAP The MCU detected incorrect data in the Yellow drum cartridge CRUM.
091-921 RAP Drum CRUM is disconnected.
091-922 RAP Wrong Data in magenta drum cartridge.
091-923 RAP Wrong data in cyan drum cartridge.
091-924 RAP The CRUM authentication registration data on the yellow drum cartridge is incorrect.
091-925 RAP Wrong data in yellow Magenta cartridge.
091-926 RAP The CRUM authentication registration data on the cyan drum cartridge is incorrect.
091-927 RAP Yellow Drum CRUM is disconnected.
091-928 RAP Magenta Drum CRUM is disconnected.
091-929 RAP Cyan Drum CRUM is disconnected.
091-932 RAP The yellow drum cartridge (Y) has reached the end-of-life.
091-933 RAP The magenta drum cartridge (M) has reached the end-of-life.
091-934 RAP The cyan drum cartridge (C) has reached the end-of-life.
092-649 RAP The MOB ADC Shutter remains open due to shutter failure.
092-650 RAP The MOB ADC Shutter remains closed due to shutter failure.
092-651 RAP The output read by ADC Sensor from the clean Photoreceptor surface is out of range.
092-652 RAP The measured ADC Patch density is light. (Over 75% of Vclean).
092-653 RAP ATC SNR-Yellow output signal failure.
092-654 RAP ATC SNR-Magenta output signal failure.
092-655 RAP ATC SNR-Cyan output signal failure.
092-656 RAP ATC SNR-black output signal failure.
RAP The amplitude of ATC Yellow Sensor output is out of range.
RAP The amplitude of ATC Magenta Sensor output is out of range.
RAP The amplitude of ATC Cyan Sensor output is out of range.
RAP The amplitude of ATC Black Sensor output is out of range.
RAP The temperature output of the environment sensor is out of range.
RAP The humidity output of the environment sensor is out of range.
RAP The two levels of ADC Patch density created in Mini-Setup are reversed.
093-300 RAP Marking Drawer Interlock Open.
93-313 RAP The Low Toner Sensor failed to detect any toner after the Toner Cartridge Motor was energized.
93-314 RAP Yellow Dispense failure. 093-315 RAP Magenta Dispense failure.
093-316 RAP Cyan Dispense failure.
093-317 RAP Black Dispense failure.
093-320 RAP There was a problem with the developer motor rotation.
093-421 RAP The Black Toner Cartridge (K1) is empty and the Black Toner Cartridge (K2) is near empty.
093-422 RAP The Black Toner Cartridge (K2) is empty and the Black Toner Cartridge (K1) is near empty.
093-423 RAP Yellow toner is near empty.
093-424 RAP Magenta toner is near empty.
093-425 RAP Cyan toner empty.
093-600 RAP Yellow Dispense near failure.
093-601 RAP Magenta Dispense near failure.
093-602 RAP Cyan Dispense near failure.
093-603 RAP Black Dispense near failure.
093-912 RAP The Black Dispense Motor rotation timed out indicating that the Black Cartridge and Reserve Tank are empty.
093-918 RAP A communication failure with Black Toner Cartridge CRUM K2.
RAP A communication failure with Black Toner Cartridge CRUM K1.
RAP The data written to the toner CRUM K1 did not agree with the data read.
RAP Toner Cartridge CRUM K1 Authentication Data is different.
RAP A communication failure with Yellow Toner Cartridge CRUM Y.
RAP A communication failure with Magenta Toner Cartridge CRUM M.
RAP A communication failure with Cyan Toner Cartridge CRUM C.
093-932 RAP Cartridge Exchange Time Over.
093-934 RAP The data written to the toner CRUM M did not agree with the data read.
093-935 RAP The data written to the toner CRUM C did not agree with the data read.
093-936 RAP The data written to the toner CRUM K2 did not agree with the data read.
093-937 RAP Toner Cartridge CRUM Y Authentication Data is different.
093-938 RAP Toner Cartridge CRUM M Authentication Data is different.
093-939 RAP Toner Cartridge CRUM C Authentication Data is different.
093-940 RAP Toner Cartridge CRUM K2 Authentication Data is different.
94-320 RAP Retraction was not detected within the specified time after retraction of the 1st BTR started.
94-321 RAP First BTR Contact Failure.
094-322 RAP Second BTR Retract Failure.
094-323 RAP Contact was not detected within the specified time after contact with the 2nd BTR started.
Looking for a new Xerox that works?
Check out this beauty – Altalink C8030
ABOUT USA Copier Lease
USA Copier Lease is an exclusive Xerox dealer with clients across the United States. We can service and support your Xerox devices anywhere in the United States with a guaranteed same day / next day on-site service guarantee.
In addition, to learn more about how USA Copier Lease can help your organization evaluate existing copier leases or provide a quote for new copier, call (800) 893 1183 or send an email to online@usamagnum.com
Решение проблем
Xerox
®
WorkCentre
®
5022/5024 Multifunction Printer
User Guide
13-59
Застревание оригиналов
Когда в податчике застревает оригинал, аппарат прекращает работу и раздается
предупреждающий сигнал. На экране также появляется соответствующее сообщение.
Note
В конфигурации некоторых моделей податчик оригиналов в стандартную комплектацию
не входит.
Для извлечения застрявшего оригинала выполните следующие действия.
1.
Потяните вверх за переднюю ручку крышки податчика оригиналов и полностью откройте
крышку.
Note
В полностью открытом положении крышка фиксируется. Медленно откройте крышку.
Код ошибки
Сообщение
005-122
005-123
005-125
005-131
005-132
005-134
005-135
005-136
005-139
005-145
005-147
005-196
005-198
005-199
005-907
005-908
005-913
Застр-е в податчике ориг-в
Откройте крышку податчика и вытащите бумагу.
005-197
Нет такого формата ориг-ла
Откройте крышку податчика и вытащите бумагу.
- 29 сентября 2016 12:02:23
- Просмотров: 224452
-
Xerox WC-5335 модуль узла термофиксатора.
Трудно поверить в его восемь лет с тех пор, как мы впервые принял хороший вид на C123 стиле термоэлемент модули. А также Xerox любит этой машины для основания и не были еще два волны новых моделей с тех пор в котором термоэлемент проекты были почти идентичны. Старый термоэлемент восстановления статьи по-прежнему хороший, но в более поздних моделей на протяжении ряда лет делает эти ценности пересмотра. Сначала мы обратимся в номера по каталогу для термоэлементы найти в новые модели этой серии. Затем мы рассмотрим важность обновления встроенного ПО и как перейти по этому поводу. И наконец мы будем перейти на термоэлемент связанных кодов неисправностей и настройки температуры для вас доступны в NVM.
Каждое новое семейство моделей имеет свои собственные номера по каталогу для термоэлемента. Хорошая новость заключается в том, что детали в этих термоэлементы, в том числе теплового стабилизатора поперечной устойчивости и давление вальцов, все из одной версии термоэлемента к следующему. Процедура для восстановления каждого является таким же образом. Здесь находятся номера деталей для термоэлементы для каждой семьи в модели:
-C123 семейство CC-C123/C128/C133, WC-M123/M128/M133, Pro123/Pro128/Pro133: 126K16480, 126K16481, 604K20342, 604K20343, 604K20344, 622S00191
-WC-5230 семейство (WorkCentre) WC-5222/5225/5230: 126K24980, 126K24981
-WC-5335 семейство WC-5325/5330/5335: 126K29391, 126K29392, 126K29393, 126K29394, 126K29395
Эти модели все очень привередливы насчет температуры термоэлемента и время цикла нагревания при запуске. Клиенты должны быть осведомлены о том, что если машина стоит в холодном помещении и при попытке запустить его, он, скорее всего, не готов; это время и называют “неспособность согреться во время” типа код неисправности. Некоторые из этих кодов требуется сбросить ошибку из диагностического режима (который мы рассмотрим позже в этой статье).
Также мы выяснили, что на WC-5335 семьи в частности, очень важно обновить прошивку на машине, потому что они уже исправлены несколько проблем, связанных с термоблоком. Один известный поисковой проблема в термопленки работает слишком жарко. Тонер осыпается на странице, если вы мажете на площадь тяжелую почву. Затем тонер начнет смещение на страницах и на термисторы, что дает вам еще жарче, пока черные рукава-как покрытие прижимного ролика палочки для жары крена и отслаивается лоскутами. В книге сказано, что WC 5325/5330/5335 машины все должны быть обновлены до версии 53.30.11 или выше.
Вы можете перейти и загрузить прошивку от www.support.xerox.com (которая является большим ресурсом для любых потребностей клиента, как изменение настроек системного администратора или перезагрузкой микропрограммы и т.д.). На сайте поддержки вы введите модель машины и выберите либо «поддержки» или «Драйверы и загружаемые материалы» для правильного модель из списка. В этом случае выберите «Драйверы и загружаемые материалы» и прокрутите вниз до нижней части где прошивки выбор не найдено.
Обновления программного обеспечения на 5335 семьи с флэш-накопителя USB:
Создать папку на флэш-накопитель USB и имя его «DWLD». Скопируйте файл с расширением .bin файл получен от support.xerox.com сайт. Он поставляется в формате ZIP, распакуйте архив и скопируйте и вставьте его в новую папку. Убедитесь в печати через USB-порт включен, а затем полностью выключить машину. Вам необходимо отключить оба выключателя питания (один находится внутри передней крышки). Пробку в флэш-накопитель USB в разъем USB на панели управления (если доступно).
Чтобы очистить термоэлемент коды неисправности и также для сброса HFSI (Высокая частота элемент обслуживания) Счетчики вам нужно перейти в режим диагностики. Начало в диагностика немного отличается на старых моделей (C123 семьи), но это все еще довольно близко:
Ввод пользовательский интерфейс (пользовательский интерфейс) режим диагностики:
Из включенном состоянии, нажмите и удерживайте кнопку “0” в течение шести секунд, а затем нажать кнопку “Старт”, продолжая удерживать кнопку “0”. Машина будет запрашивать пароль. Введите доступа по умолчанию количество “6789” и нажмите кнопку “подтвердить”. На дисплее будет признать, что теперь вы находитесь в режиме диагностики (на семью C123, цвета на дисплее будут обратными). Далее нажимаем “состояние машины” кнопку (или “вход/выход” для C123Family). Выберите вкладку “инструменты”, затем “системные настройки”, “Общие настройки”, “техническое обслуживание/диагностика.” Это приведет вас в Главное меню, где вы найдете настройки памяти (НВМ) и много других важных вещей. Счетчики HFSI для сброса термоблока граф и другие высокочастотные элементы обслуживания находится в “Настройки/Прочие”.
Теперь давайте взглянуть на список кодов неисправностей, которые нужно сделать с термоблоком.
Термоблок коды состояния и как восстановить их.
C123 и WC-5230 семьи: (C123/128/133, М123/128/133, Pro123/128/133, WC-5222/5225/5235)
WC-5335 семьи: (WC-5325/5330/5335)
* Сброс Фьюзера Коды (010-320, 010-327, 059-315, & 059-317)
Достигнуто путем сброса NVM 744-220 код “0”, или 744-005 для WC-5335 семьи.
Сначала введите пользовательский интерфейс (пользовательский интерфейс) диагностический режим (см. выше для деталей).
Когда вы находитесь в меню обслуживание/диагностика, вы увидите среди прочего выбор называется “NVM чтение/запись” (nvm в энергонезависимой памяти). Теперь вы можете ввести ваш звена цепи код (в данном случае 744-220, или 744-005 к WC-5335 семьи, и нажмите “подтвердить/изменить”. Текущее значение будет отображаться (если машина находится в термоблок неисправность, то значение будет установлено в “1, 2, 3 или 4, в зависимости от конкретной неисправности). Выберите “новое значение” столбца и введите новое значение (“0”). Выберите “Сохранить” и новый номер должен появиться в колонке “текущие значения”. Выберите “Распродажа” для перезагрузки. Аппарат будет пытаться снова прогрев термоэлемента. Если условие, которое вызвало виноват в первую очередь все-таки происходит, код состояния вернется через несколько минут, пытаясь согреться.
Если у вас есть упрямые машина, которая держит время, когда он включен по утрам, некоторые люди сообщили, что изменения NVM памяти настройки 744-043 на “1” продлевает допустимое время прогрева. Это помогает сделать машину, чтобы быть более снисходительными. Все-таки это важно, что владелец машины держать его в помещении, которое не слишком холодно ночью. Если в комнате слишком холодно, когда они включить машину, он, скорее всего, перейдет в коду неисправности, необходимо прийти техник превратить код из диагностики. Вы хотите, чтобы внимательно проверить фьюзинг после изменения каких-либо термоблок настройки, чтобы убедиться, что там все предохранители при различных обстоятельствах, потому что вариаций на прошивку может сделать одна машина вести себя немного отличается от другого.
Есть еще одна вещь, которая окажется полезной при проверке термоблока вы собираетесь восстановить. Вы хотите знать, какие контакты для чего схемы внутри термоблока. Есть две инфракрасные лампы, которые фактически объединены в одном фонаре, чтобы проверить. Эти оба разделяют общую обратный кабель, который проходит через термостат (термопредохранитель). Если в термопленки достаточно сильно перегрет, термостат будет взорван и должны быть заменены. Есть также два термисторы, задний перегрев термистора и центр управления термистор.
Здесь представлены пин-аутов для каждого термоэлемента комплектующих для C123 и WC-5230 семьи и WC-5335 семьи.
Обратите внимание, что C123 и WC-5230 семьи являются взаимозаменяемыми, но на WC-5325 пин-код-это совершенно разные и они ушли так далеко, чтобы перевернуть разъем над. Проверьте две фотографии справа.
C123 или WC-5230 семьи
WC-5335 семьи
Любой из двух тепла лампы схемы должна измерить 100 Ом или меньше, и термисторы должны прочитать за 3К ом, если они хорошие.
Каждый светильник жары цепи проходит один и тот же термостат (термопредохранитель) и обратно через один и тот же свинец.
Это должно привести всех в курс дела на новой смертные, слившиеся в этом стиле ксерокс копиры. Вы можете получить термоблока восстановить инструкции, . Это довольно просто, хотя как обычно полезно иметь учебные, чтобы помочь сократить кривую обучения немного.
Заказать восстановление эти смертные, слившиеся всех!
Решение проблем
Xerox
®
WorkCentre
®
5022/5024 Multifunction Printer
User Guide
13-59
Застревание оригиналов
Когда в податчике застревает оригинал, аппарат прекращает работу и раздается
предупреждающий сигнал. На экране также появляется соответствующее сообщение.
Note
В конфигурации некоторых моделей податчик оригиналов в стандартную комплектацию
не входит.
Для извлечения застрявшего оригинала выполните следующие действия.
1.
Потяните вверх за переднюю ручку крышки податчика оригиналов и полностью откройте
крышку.
Note
В полностью открытом положении крышка фиксируется. Медленно откройте крышку.
Код ошибки
Сообщение
005-122
005-123
005-125
005-131
005-132
005-134
005-135
005-136
005-139
005-145
005-147
005-196
005-198
005-199
005-907
005-908
005-913
Застр-е в податчике ориг-в
Откройте крышку податчика и вытащите бумагу.
005-197
Нет такого формата ориг-ла
Откройте крышку податчика и вытащите бумагу.
The most common error codes.
| Error | |
|---|---|
| 041-310 | Description: IM Logic Fail RAP The IM (Image Management) software control error was detected. |
| 062-396 | Description: CCD Cable Connection Fail RAP A CCD Flat Cable connection error was detected. |
| 024-912 | Description: Tray 3 Size Mismatch RAP Operation Error. Size Mismatch Tray 3: Measured Length Mismatch. When the paper slow scan direction length is measured on the paper path, the length is different from the slow scan length for the size detected by the |
| 005-940 | Description: DADF No Original RAP Operation Fail. Final document correction notification due to DADF document being pulled out. |
| 012-291 | Description: (Integrated Finisher) Stapler Fail RAP Within a specified time after the Staple Motor started rotating in reverse direction, the Staple Head Home Sensor was never detected turning On. |
| 041-310 | Description: IM Logic Fail RAP The IM (Image Management) software control error was detected. |
| 062-396 | Description: CCD Cable Connection Fail RAP A CCD Flat Cable connection error was detected. |
| 005-940 | Description: DADF No Original RAP Operation Fail. Final document correction notification due to DADF document being pulled out. |
| 012-212 | Description: Stacker Tray Upper Limit Failure RAP (LX) The stacker has continued to elevate after the defined period of time has passed since Stacker No Paper Sensor is ON during stacker elevation. |
| 024-912 | Description: Tray 3 Size Mismatch RAP Operation Error. Size Mismatch Tray 3: Measured Length Mismatch. When the paper slow scan direction length is measured on the paper path, the length is different from the slow scan length for the size detected by the |
-
Code Description010-330 Fusing Unit Motor Fail010-360 IH Driver
Input High Voltage Fail010-361 IH Driver Input Low Voltage
Fail010-362 IH Driver Surge Fail010-363 IGBT Temperature High Fail
010-364 IGBT Temperature Sensor Fail 010-367 Input Low Current Fail
010-368 Encoder Pulse Fail 010-369 IH Driver Communication
Fail010-370 IH Driver Freeze Fail010-371 Heat Belt STS Center
Disconnection Fail 010-372 Heat Roll STS Center Over Temperature
Fail 010-373 Heat Belt STS Rear Disconnection Fail 010-374 Heat
Belt STS Rear Over Temperature Fail010-375 Heat Belt STS Center
Warm Up Time Fail010-376 Heat Belt STS Rear Warm Up Time
Fail010-377 Fusing Unit On Time Fail 010-378 Heat Belt Rotation
Fail 010-379 Fusing Unit Hot Not Ready Return Time Fail010-380
P/Roll Latch Motor Fail 010-381 Fusing Unit Assy Illegal Fail
010-382 Fusing Unit Thermostat Fail010-398 Fusing Unit Fan Fail
010-420 Fusing Unit Near Life Warning010-421 Fusing Unit Life Over
Warning041-310 IM Logic Fail041-316 IH Driver Interface Fail
041-317 MCU IH Interface Fail041-325 MCU PWB F2 Blows041-326 MCU
PWB F3 Blows041-327 MCU PWB F4 Blows041-328 MCU PWB F5 Blows041-340
MCU Nvm (EEPROM) Data Fail 041-341 MCU NVM (EEPROM) Access
Fail041-342 MCU Nvm (EEPROM) Buffer Fail041-345 MD PWB F2
Blows041-347 Serial I/O Fail 041-348 MD PWB F4 Blows041-349 MD PWB
F6 Blows041-350 MD PWB F7 Blows041-351 MD Detect Fail 041-352 MD
PWB F5 Blows041-353 MD PWB F8 Blows041-354 MD PWB F9 Blows041-355
MD PWB F10 Blows041-356 MD PWB F11 Blows041-357 MD PWB F12
Blows041-358 MD PWB F13 Blows041-359 MD PWB F14 Blows -
Code Description041-360 MD PWB F15 Blows041-361 MD PWB F16
Blows041-368 MCU-SW Firmware Mismatch041-369 MD Type Mismatch
042-320 Drum Y, M, C Motor Fail 042-323 Drum K Motor Fail042-324
IBT Motor Fail042-325 Main Motor Fail 042-330 IH Exhaust Fan
Fail042-332 IH Intake Fan Fail042-335 Process 1 Fan Fail 042-336
Process 2 Fan Fail 042-337 NOHAD Logic Fail042-338 LVPS Front Fan
Fail042-340 Cartridge Fan Fail 042-341 M Fan Fail 042-342 Suction
Fan Fail 042-343 Rear Bottom Fan Fail042-344 C Exhaust Fan
Fail042-400 Deodorant Filter Life End 042-604 NOHAD Temperature
Sensor Fail 042-609 LH Fan Fail045-310 Image Ready NG045-311
Controller Communication Fail045-312 Drive Logic Fail045-313
ENG_LOGIC_FAIL045-321 MK_Panel_NG045-322 MK_Pitch_NG045-331
MK_MKIF_MSG_Reject 045-332 MK_MMIF_MSG_Reject 045-350
MK_Emergency_Over_Wait045-351 MK_Emergency_No_Timer045-352
MK_Emergency_Enforced_Stop 045-370 LPH Power On Fail Multi045-371
LPH Download Data Fail Multi 045-372 LPH Mismatch Fail Multi045-373
LPH Read Fail Multi 045-374 LPH Write Fail Multi045-375 LPH Act
Fail Multi045-376 LPH PLL Lock Fail Multi 047-211 Exit 1 OCT Home
Fail047-212 Exit 2 OCT Home Fail 047-213 Finisher Kind Mismatch
047-216 Finisher Communication Fail047-217 Feeder Communication
Fail 047-320 ALL Destination Tray Broken 061-350 LPH Power On Fail
Y 061-351 LPH Power On Fail M061-352 LPH Power On Fail C -
Code Description061-353 LPH Power On Fail K 061-354 LPH Download
Data Fail Y 061-355 LPH Download Data Fail M061-356 LPH Download
Data Fail C 061-357 LPH Download Data Fail K061-358 LPH Mismatch
Fail Y 061-359 LPH Mismatch Fail M 061-360 LPH Mismatch Fail
C061-361 LPH Mismatch Fail K061-362 LPH Read Fail Y061-363 LPH Read
Fail M061-364 LPH Read Fail C 061-365 LPH Read Fail K061-366 LPH
Write Fail Y 061-367 LPH Write Fail M 061-368 LPH Write Fail
C061-369 LPH Write Fail K061-370 LPH Act Fail Y 061-371 LPH Act
Fail M 061-372 LPH Act Fail C061-373 LPH Act Fail K061-374 LPH Chip
Fail Y 061-375 LPH Chip Fail M 061-376 LPH Chip Fail C061-377 LPH
Chip Fail K 061-378 LPH Chip Fail Y 061-379 LPH Ltrg Fail M 061-384
LPH Ltrg Fail C 061-385 LPH Ltrg Fail K061-386 LPH PLL Lock Fail Y
061-387 LPH PLL Lock Fail M 061-388 LPH PLL Lock Fail C061-389 LPH
PLL Lock Fail K061-390 LPH FFC Connect Posi Fail Y 061-391 LPH FFC
Connect Posi Fail M061-392 LPH FFC Connect Posi Fail C061-393 LPH
FFC Connect Posi Fail K061-394 LPH FFC Connect Nega Fail Y061-395
LPH FFC Connect Nega Fail M061-396 LPH FFC Connect Nega Fail
C061-397 LPH FFC Connect Nega Fail K061-398 BITZ1 Initialize
Fail061-399 BITZ2 Initialize Fail061-610 Bitz1 CONTIF Fail061-611
Bitz2 CONTIF Fail071-105 Regi Sensor On Jam (Tray1/2/3/4)071-210
Tray 1 Lift Up Fail071-212 Tray 1 Paper Size Sensor Broken071-940
Tray 1 Lift Up NG -
Code Description072-101 Tray 2 Miss Feed072-102 Feed Out Sensor
2 On Jam (Tray 3/4)072-210 Tray 2 Lift Up Fail072-212 Tray 2 Paper
Size Sensor Broken 072-900 Tray 2 Feed Out Sensor Static Jam072-940
Tray 2 Lift Up NG073-101 Tray 3 Miss Feed 073-102 Feed Out Sensor 3
On Jam (Tray 4) 073-210 Tray 3 Lift Up Fail073-212 Tray 3 Paper
Size Sensor Broken073-900 Tray 3 Feed Out Sensor Static Jam073-940
Tray 3 Lift Up NG 074-101 Tray 4 Miss Feed074-210 Tray 4 Lift Up
Fail074-212 Tray 4 Paper Size Sensor Broken074-900 Tray 4 Feed Out
Sensor Static Jam074-940 Tray 4 Lift Up NG 075-100 MSI Miss
Feed075-103 MSI Feed Out Sensor Off Jam075-135 Regi Sensor On Jam
(MSI) 075-212 MSI Nudger Up Down Fail077-101 Regi Sensor Off
Jam077-103 Exit Sensor 1 Off Jam077-104 Exit Sensor 1 Off Jam (Too
Short)077-105 Exit Sensor 2 Off Jam 077-106 Exit Sensor 1 On Jam
077-109 Exit Sensor 2 On Jam077-110 POB Sensor On Jam077-130 Regi
Sensor On Jam (Duplex Direct)077-131 Duplex Wait Sensor On Jam
077-211 Tray Module Kind Mismatch077-212 Tray Module Reset Fail
077-214 Tray Module Logic Fail 077-215 Tray Module Communication
Fail077-300 Front Cover Interlock Open077-301 L/H Cover Interlock
Open077-305 Tray Module L/H Cover Open077-307 Duplex Cover
Open077-308 L/H High Cover Open 077-314 P/H Module Logic Fail
077-320 All Feed Tray Broken 077-602 Transparency Sensor
Fail077-900 Regi Sensor Static Jam077-901 Exit Sensor 1 Static
Jam077-902 Exit Sensor 2 Static Jam 077-903 POB Sensor Static
Jam077-907 Duplex Wait Sensor Static Jam089-600 RC Sample Lateral
Fail-A1 089-601 RC Sample Block Fail-A1-In -
Code Description089-603 RC Sample Block Fail-A1-Out089-604 RC
Sample Block Fail-B-#1-In089-606 RC Sample Block
Fail-B-#1-Out089-607 RC Sample Block Fail-B-#2-In089-609 RC Sample
Block Fail-B-#2-Out089-610 RC Sample Block Fail-B-#3-In089-612 RC
Sample Block Fail-B-#3-Out 089-613 RC Sample Block Fail-B-#4-In
089-615 RC Sample Block Fail-B-#4-Out089-616 RC Data Over Flow Fail
089-617 RC Lead Regi Over Range Fail089-625 RC Data Linearity Fail
Y089-626 RC Data Linearity Fail M 089-627 RC Data Linearity Fail C
089-628 RC Data Linearity Fail K091-313 CRUM ASIC Communication
Fail 091-400 Waste Toner Bottle Near Full091-401 Drum Cartridge K
Near Life091-402 Drum Cartridge K Life Over091-407 DRUM K CRUM
Trouble Info 091-411 Drum Cartridge Y Near Life091-417 DRUM Y CRUM
Trouble Info091-421 Drum Cartridge M Near Life 091-427 DRUM M CRUM
Trouble Info091-431 Drum Cartridge C Near Life091-437 DRUM C CRUM
Trouble Info091-480 Drum Cartridge Y Life Over091-481 Drum
Cartridge M Life Over091-482 Drum Cartridge C Life Over091-910
Waste Toner Bottle Not In Position091-911 Waste Toner Bottle
Full091-913 Drum Cartridge K Life End091-914 Drum CRUM K
Communication Fail091-915 Drum CRUM K Data Broken091-916 Drum CRUM
K Data Mismatch091-917 Drum CRUM Y Communication Fail091-918 Drum
CRUM M Communication Fail091-919 Drum CRUM C Communication Fail
091-921 Drum CRUM K Not In Position091-927 Drum CRUM Y Not In
Position091-928 Drum CRUM M Not In Position 091-929 Drum CRUM C Not
In Position091-940 Drum CRUM Y Data Broken 091-941 Drum CRUM C Data
Broken 091-942 Drum CRUM C Data Broken 091-943 Drum CRUM Y Data
Mismatch 091-944 Drum CRUM M Data Mismatch091-945 Drum CRUM C Data
Mismatch092-312 ATC Fail [Y] -
Code Description092-313 ATC Fail [M]092-314 ATC Fail [C]092-315
ATC Fail [K]092-649 ADC Shutter Open Fail092-650 ADC Shutter Close
Fail092-651 ADC Sensor Fail092-657 ATC Amplitude Fail [Y]092-658
ATC Amplitude Fail [M]092-659 ATC Amplitude Fail [C]092-660 ATC
Amplitude Fail [K]092-661 Temperature Sensor Fail092-662 Humidity
Sensor Fail092-665 ATC Average Fail [Y]092-666 ATC Average Fail
[M]092-667 ATC Average Fail [C] 092-668 ATC Average Fail [K]092-670
ADC Patch Fail [Y] 092-671 ADC Patch Fail [M]092-672 ADC Patch Fail
[C] 092-673 ADC Patch Fail [K] 092-675 ADC Mini Setup Fail
[Y]092-676 ADC Mini Setup Fail [M]092-677 ADC Mini Setup Fail [C]
092-678 ADC Mini Setup Fail [K]093-314 Y Disp Motor Fail093-315 M
Disp Motor Fail 093-316 C Disp Motor Fail093-317 K Disp Motor
Fail093-324 Deve Y ,M,C Motor Fail 093-400 K Toner Cartridge Near
Empty 093-406 K Toner Cartridge Pre Near Empty 093-407 Y Toner
Cartridge Pre Near Empty 093-408 M Toner Cartridge Pre Near
Empty093-409 C Toner Cartridge Pre Near Empty 093-423 Y Toner
Cartridge Pre Near Empty 093-424 M Toner Cartridge Near Empty
093-425 C Toner Cartridge Near Empty093-426 TONER K CRUM Trouble
Info 093-427 TONER Y CRUM Trouble Info 093-428 TONER M CRUM Trouble
Info093-429 TONER C CRUM Trouble Info 093-912 K Toner Cartridge
Empty093-916 Toner K CRUM Not In Position 093-924 Toner K CRUM
Communication Fail093-925 Toner K CRUM Data Broken Fail093-926
Toner K CRUM Data Mismatch Fail 093-941 Toner M CRUM Communication
Fail093-942 Toner C CRUM Communication Fail093-943 Toner Y CRUM
Communication Fail -
Code Description093-950 Toner Y CRUM Data Broken Fail093-951
Toner M CRUM Data Broken Fail 093-952 Toner C CRUM Data Broken
Fail093-960 Toner Y CRUM Data Mismatch Fail 093-961 Toner M CRUM
Data Mismatch Fail 093-962 Toner C CRUM Data Mismatch Fail093-970
Toner Y CRUM Not In Position093-971 Toner M CRUM Not In
Position093-972 Toner C CRUM Not In Position094-300 IBT Front Cover
Open094-320 1st BTR Contact/Retract Fail 094-323 2nd BTR
Contact/Retract Fail 094-417 IBT Unit Near End Warning 094-418 IBT
CLN Unit Near End Warning 094-419 2nd BTR Unit Near End
Warning094-420 IBT Unit End Warning 094-421 IBT CLN Unit End
Warning 094-422 2nd BTR Unit End WarningOF-01 Common System
FailOF-02 HDD System FailOF-03 NET/USB System FailOF-04 Panel
System FailOF-05 IIT System FailOF-06 IOT System FailOF-07 FAX
System Fail OF-08 116-324 FailOF-09 Common Job Fail OF-10 HDD Job
FailOF-11 FAX Job FailOF-12 033-363 FailOF-13 016-782 / 016-784
Fail OF-14 FAX Card Fail OF-15 NET Job Fail OF-30 [No Error Code]
(No problems during service call) OF-31 [No Error Code] (Problem:
«Does not start up at power ON» error can beOF-32 [No Error Code] (Problem: «Does not return from Power
Save» error can bereproduced.)OF-33 [No Error Code] (Problem: «Remained in ‘Copying…’ or
‘Printing…'» error can bereproduced.)003-318 IITsc Soft
Fail0003-319 IITsc Video Driver Detection Fail003-320 IISS-ESS
Communication Fail 1003-321 IISS-ESS Communication Fail 2003-322
IISS-ESS Communication Fail 3003-323 IISS-ESS Communication Fail
4003-324 IISS-ESS Communication Fail 5003-325 IISS-ESS
Communication Fail 6003-326 IISS-ESS Communication Fail 7003-327
IISS-ESS Communication Fail 8003-328 IISS-ESS Communication Fail
9 -
Code Description003-329 IISS-ESS Communication Fail 10003-330
IISS-ESS Communication Fail 11003-331 IISS-ESS Communication Fail
12003-332 IISS-ESS Communication Fail 13003-333 IISS-ESS
Communication Fail 14003-334 IISS-ESS Communication Fail 15003-335
IISS-ESS Communication Fail 16003-336 IISS-ESS Communication Fail
17003-337 IISS-ESS Communication Fail 18003-338 IISS-ESS
Communication Fail 19003-339 IISS-ESS Communication Fail 20003-340
IISS-ESS Communication Fail 21003-341 IISS-ESS Communication Fail
22003-342 IISS-ESS Communication Fail 23003-343 IISS-ESS
Communication Fail 24003-344 IISS_ESS X Hotline Fail PowerOn
003-345 X PIO Unmatch Fail 1003-346 X PIO Unmatch Fail 2003-700
Returned a lot of Documents error003-701 Duplication prevention
code detect003-702 Different magnification, for surface and back of
a document003-703 Auto Color Correction Patch Position Fail003-704
Color Correction Value Difference Fail003-705 Paper Size Mismatch
of the Energy Saving Return Fail003-750 Book Duplex-Insufficient
Docs 003-751 Under P ANTHER Capacity (Scan)003-752 Cannot scan
600DPI 003-753 Cannot scan over 300DPI003-754 S2X recoverable
error003-755 S2X command error003-756 S2X command error 003-757
Cannot scan over 400DPI003-760 Scan Settings Error 003-761
Incorrect Paper Tray Size003-763 Adjustment Chart Not Found003-764
Document insufficient (image overlay)003-780 Scan Image Compression
Error 003-795 AMS Limit Error 003-930 Cannot scan over
300DPI003-931 Cannot scan over 400DPI003-932 Cannot scan 600DPI
003-933 Next Documents Cannot scan over 300DPI003-934 Next
Documents Cannot scan over 400DPI003-935 Next Documents Cannot scan
over 600DPI003-940 DAM memory insufficient 003-941 Page memory
insufficient003-942 Document size Auto Detect error003-944 Image
repeat count fail003-946 Every direction difference (Copy APS) -
Code Description003-947 Return Documents counts error 003-948
Return Documents mismatch003-951 1job max page over003-952 Return
Documents Color mismatch003-955 Documents size exchange
error003-956 Documents size unknown error003-963 No APS object
Tray003-965 ATS/APS No Paper (IITsc Detect)003-966 ATS/APS No
Destination (IITsc)003-967 DADF APS No Destination003-968 Punch
position error 003-969 Punch size error003-970 FAX Line Memory
Overflow003-971 prevention code detect with the right to
cancel003-972 Maximum Stored Page Over Flow003-973 Every direction
difference003-974 Next Original Specification 003-976 FAX Line
Memory Overflow (N up) 003-977 Document Miss Match (Multi
Scan)003-978 Color Document Miss Mutch (Multi Scan)003-980 Staple
position error 003-981 Staple size error 003-982 IIT sc HDD access
error 005-500 Write to DADF-ROM error detection (During DLD
method)005-940 DADF No Original005-941 Doc number of sheets is
insufficient005-942 Doc fault loading on DADF005-945 Document guide
set mistake005-946 Manuscript reading equipment obstacle
detection005-947 Document guide set mistake 2005-948 Manuscript
reading equipment obstacle detection007-954 SMH size
mismatch007-959 OHP kind mismatch (Not white frame OHP)007-960
Paper kind mismatch007-969 CentreTray full stack011-941 MBX #01 Bin
Full Stack011-942 MBX #02 Bin Full Stack011-943 MBX #03 Bin Full
Stack011-944 MBX #04 Bin Full Stack011-945 MBX #05 Bin Full
Stack011-946 MBX #06 Bin Full Stack011-947 MBX #07 Bin Full
Stack011-948 MBX #08 Bin Full Stack011-949 MBX #09 Bin Full
Stack011-950 MBX #10 Bin Full Stack012-500 Write to
Finisher/MACS-ROM error detection (During DLD method)012-911
Stacker Lower Safety012-914 Stacker Tray Staple Set Over
Count012-965 Stapler Pin near empty -
Code Description012-966 Scratch Sheet Compile012-969 IOT Center
Tray Full016-210 SW Option Fail (HDD Not Exist)016-211 SW Option
Fail (SysMemory Low)016-212 SW Option Fail (Page Memory Low)016-213
SW Option Fail (Printer CARD Not Exist)016-214 SW Option Fail (Fax
CARD Not Exist)016-215 SW Option Fail (JPEG boad Not Exist)016-216
SW Option Fail (JPEG boad Not Exist)016-217 SW Option Fail
(Controller ROM not Printer kit)016-218 PS KIT Not Exist for
XDOD016-219 License is required (Printer Kit)016-220 S2X
unrecoverable error016-221 S2X016-222 S2X self-diag error016-223
S2X SDRAM Error016-224 S2X PCI Reg Error016-225 S2X ROM CheckSum
Error016-226 S2X IIT Connection Error016-227 S2X016-228 S2X016-229
SW Option Fail (FCW-UI Not Exist)016-230 License is required (PS
ImageLog Kit)016-231 SW Option Fail (Image Ext PWB Not
Exist)016-232 MRC HW Initialize Error 016-233 SW Option Fail (USB
Host Not Exist)016-234 XCP Out of Memory Error016-235 XCP Internal
Error 016-236 XCP not active016-237 Auth plugin not active016-238
Custom svc not active016-239 Auth contents not exist016-240 S2X NVM
CheckSum Fail 016-241 S2X NVM CheckSum Fail 016-242 System GMT
Clock Fail 016-310 ssmm Job Log Full016-311 No Scanner that Should
Be016-312 SW Option Fail (Hybrid WaterMark Not Exist)016-313 Hybrid
WaterMark setting mismatch016-314 SW Option Fail (Hybrid WaterMark
Not Exist)016-315 IIT Interface Fail016-316 Page Memory Not
Detected016-317 Page Memory Broken- Standard 016-318 Page Memory
Broken- Option016-319 Long Boot Diag IIT Interface Fail 016-320
Document Formatter Fatal Error 016-321 Fax Module Error016-322 JBA
Account Full016-323 B-Formatter Fatal Error -
Code Description016-324 Scheduled Image Overwrite016-325 Using
Personal Certificate016-326 Cont-UI Cable Connection Fail016-327
BackPlane Connection Fail 016-328 Cont-MCU Cable Connection Fail
016-329 Long Boot Diag Page Memory Not Detected Fail 016-330 Cont
System Memory Fail-1016-331 Cont System Memory Fail-2016-332 Cont
System Memory Fail-3016-333 Long Boot Diag Page Memory Broken
Standard Fail016-334 Long Boot Diag Page Memory Broken Option
Fail016-335 Cont ProgramROM Fail-1016-336 Cont ProgramROM
Fail-2016-337 Cont ProgramROM Fail-3016-338 Cont FontROM
Fail-1016-339 Cont FontROM Fail-2016-340 Cont FontROM Fail-3016-341
Cont FontROM Fail-4016-342 Cont RTC Fai016-343 Long Boot Diag Timer
Fail016-345 Cont NV-Memory Fail016-346 Cont A4FAX Modem Diagnosis
Fail 016-347 Cont PageMemory Fail016-348 Cont PageMemory
Fail-2016-349 Cont MAC Address Data Fail016-350 Cont SEEP-ROM
Fail-1016-351 Cont SEEP-ROM Fail-2016-360 Cont UI Fail-1016-362
Cont UI Fail-2016-363 Cont LyraCard Fail 016-364 Cont USB20 Host
Fail 016-365 Cont USB20 Device Fail016-366 Cont HDD Fail-1016-367
Cont HDD Fail-2016-368 Cont Torino Fail 016-369 Cont S2X PWB
Fail016-370 Cont Fail 016-371 Cont USB11 Host Fail 016-372 Cont HDD
FileSystem Fail-A016-373 Cont HDD FileSystem Fail-B016-374 Cont HDD
FileSystem Fail-C016-375 Cont HDD FileSystem Fail-D016-376 Cont HDD
FileSystem Fail-E016-377 Cont HDD FileSystem Fail-F016-378 Cont HDD
FileSystem Fail-G016-379 Cont HDD FileSystem Fail-H016-380 Cont HDD
FileSystem Fail-I016-381 Cont HDD FileSystem Fail-I016-382 Cont HDD
FileSystem Fail-P -
Code Description016-400 8021x authentication failure016-401
8021x EAP type not supported 016-402 8021x authentication failure
by timing out016-403 8021x certificate failure 016-404 8021x inside
failure016-405 Certificate DB File error016-406 8021x client
certificate failure016-407 XCP Plugin Secrity Exception 016-408 XCP
Invalid Plugin016-409 XCP Plugin Version Incompatible016-410
XCP_PLUGIN_PROPERTY_INVALID016-411
XCP_UNSUPPORTED_CLASS_VERSION016-412 XCP Plugin Misc Error016-413
Couldnt detect proxy server automatically016-414 Couldnt connect to
Xerox server or proxy016-415 Connection to Xerox server has timed
out016-416 An invalid state message received from server016-417
Invalid network settings were found016-450 SMB Host name
duplicated016-453 Dynamic DNS — IPv6 NG 016-454 DNS renewal failure
of dynamic 016-455 SNTP server time out 016-456 SNTP time
asynchronous016-461 Under non-transmitted image log
stagnation016-500 Write to Cont-ROM error detection (During DLD
method)016-501 Write to S2X-ROM error detection (During DLD
method)016-502 Write to Cont/S2X/IISS/DADF/IOT/Fin/FaxCard error
detection (During PJLmethod)016-503 SMTP Server Fail for
Redirector016-504 POP Server Fail for Redirector016-505 POP
Authentication Fail for Redirector 016-506 Image Log HDD
Full016-507 ImageLog Send Fail01016-508 ImageLog Send Fail02016-509
ImageLog No Send Rule01016-510 ImageLog No Send Rule02016-511
ImageLog Invalid Send Rule01016-512 ImageLog Invalid Send
Rule02016-513 SMTP server reception error016-514 XPS Error016-515
XPS Short of Memory 016-516 XPS PrintTicket description
error016-517 PS Booklet Illegal Color Mode Change016-518 PS Booklet
Conflict WM016-519 Device DV — Reached Limit016-520 MRC HW Job
Error016-521 SmartCard Not Found016-522 LDAP SSL error 112016-523
LDAP SSL error 113016-524 LDAP SSL error 114 -
Code Description016-525 LDAP SSL error 115016-526 LDAP SSL error
116016-527 LDAP SSL error 117016-528 SmartCard Not Auth016-529
Remote Download server timeout016-533 Kerberos Attestation protocol
error 37016-534 Kerberos Attestation protocol error 41,42016-535
Remote Download file access error016-536 Host name solution error
in Remote Download016-537 Remote Download server connection
error016-538 Remote Download file write error016-539 Kerberos
Attestation protocol error other016-543 Attestation Agent error
543016-545 Attestation Agent error 545016-546 Attestation Agent
error 546016-548 Attestation Agent error 548016-553 Attestation
Agent error 553016-554 Attestation Agent error 554016-555
Attestation Agent error 555016-556 Attestation Agent error
556016-557 Attestation Agent error 557016-558 Attestation Agent
error 558016-559 Remote Download parameter error016-560 Attestation
Agent error 560016-562 ADetected user duplication, in a cert
agent016-563 ImageLog Memory Full (Exp Kit016-564 Remote Download
Server Authentication Failed016-565 Backup Restore Error016-566
Backup Restore Condition Error016-567 Backup Capacity Full 016-568
Backup Restore Failed016-569 Attestation Agent error 569 016-570
Job ticket out of memory016-571 Job ticket wrong param016-572 Job
ticket media error 016-573 Job ticket parse error 016-574 Host name
solution error in FTP016-575 DNS server un-sets up in FTP 016-576
Server connection error in FTP 016-577 Problem in FTP
service016-578 Login name or a password error in FTP 016-579
Scanning picture preservation place error in FTP016-580 File name
acquisition failure from FTP server016-581 File name suffix limit
over in FTP016-582 File creation failure in FTP 016-583 Lock folder
creation failure in FTP016-584 Folder creation failure in FTP
016-585 File delete failure in FTP016-586 Lock folder delete
failure in FTP -
Code Description016-587 Folder delete failure in FTP016-588 Data
write-in failure to FTP server016-589 Data read failure from FTP
server016-590 Data reading failure from FTP server016-591 FTP scan
filing policy injustice 016-592 NEXTNAMEDAT file access error in
FTP 016-593 Internal error in FTP Scan016-594 TYPE command failure
in FTP016-595 PORT command failure in FTP 016-596 CDUP command
failure in FTP016-597 Same name file exists in FTP servcer016-598
Email message size over016-599 Email message size over016-600 KO
Authentication Locked016-601 Illegal Access Detection016-603 HDD
not found Fail016-700 Password is under minimum figures016-701 Out
of ART EX Memory016-702 Out of Page Buffer016-703 Email To Invalid
Box 016-704 Mailbox is Full 016-705 Secure Print Fail 016-706 Max
User Number Exceeded 016-707 Sample Print Fail016-708 HD Full by
Annotation/Watermark image 016-709 ART EX Command Error 016-710
Delayed Print Fail016-711 Email transmission size limit over
016-712 Under PANTHER Capacity (I-Formtter)016-713 Security Box
Password Error016-714 Security Box is not Enable 016-715 ESCP Form
Invalid Password016-716 TIFF Data Overflow016-717 Fax/Internet FAX
Send Result Not Found016-718 Out of PCL6 Memory016-719 Out of PCL
Memory016-720 PCL Command Error016-721 Other Error 016-722 Job
cancel by staple position NG 016-723 Job cancel by punch position
NG 016-724 Complex Position Error of Staple and Punch 016-725
B-Formatter Library Image Conversion Error 016-726 PDL Auto Switch
Fail016-727 0-page document is unstorable in a MailBox016-728
Unsupported TIFF Data016-729 TIFF Data Size too Big016-730
Unsupported ART Command 016-731 Invalid TIFF Data016-732 Form not
registerd -
Code Description016-733 Destination address resolution
error016-734 Simple transmittion report invocation error016-735
Updating Job Templete016-736 Remote directory lock error016-737
Remote lock directory remove error 016-738 PS Booklet Illegal
OutPut Size016-739 PS Booklet Document Output Missmatch016-740 PS
Booklet OutPut Tray Missmatch 016-741 Download Mode NGJob
Fail016-742 Download Data Product ID Mismatch 016-743 Device
Model/Panel Type Error016-744 Download Data CheckSum Error016-745
Download Data XPJL Fatal Error 016-746 Unsupported PDF File 016-747
No memory for drawing annotation016-748 HD Full 016-749 JCL Syntax
Error 016-750 Print job ticket description error016-751 PDF Error
016-752 PDF Short of Memory 016-753 PDF Password Mismatched 016-754
PDF LZW Not Installed 016-755 PDF Print Prohibited016-756 Auditron
— Prohibit Service 016-757 Auditron — Invalid User 016-758 Auditron
— Disabled Function 016-759 Auditron — Reached Limit016-760 PS
Decompose failure 016-761 FIFO EMPTY016-762 Print LANG Not
Installed 016-763 POP server is not found 016-764 SMTP Server
Connect Error016-765 SMTP Server HD Full 016-766 SMTP Server File
System Error 016-767 Invalid E-mail Address 016-768 Invalid Sender
Address 016-769 SMTP Server Unsupported DSN016-770 The direct fax
function is canceled by NVM016-771 Scan Data Repository ERR (DNS
address) 016-772 Scan Data Repository ERR (DNS Library)016-773
Invalid IP Address 016-774 HD Full — Compression Convert016-775 HD
Full — Image Convert016-776 Image Convert ERR 016-777 HD Access
ERR-Image Convert016-778 HD Full — Scan Image Convert 016-779 Scan
Image Conversion Error016-780 HD Access ERR-Image Convert016-781
Server Connect ERR -
Code Description016-782 Server Login ERR 016-783 Invalid Server
Path016-784 Server Write ERR 016-785 Server HD Full016-786 HD
Full-Scan Write ERR 016-787 Invalid Server IP ADD 016-788 Retrieve
to Browser Failed016-789 HD Full — Job Memory 016-790 Email
fragment over016-791 File Retrieve Fail016-792 Specified Job Not
Found 016-793 MF I/O HD Full 016-794 MediaReader:Media No Insert
016-795 MediaReader:Format Error 016-796 Document insert operation
error016-797 MediaReader:Image File Read Error016-798 No
TrustMarking Option016-799 PLW Print Instruction Fail 016-910
Required Resource Not Ready (IOTsc detect)016-911 Multi-Paper
Required On A Single Tray 016-940 Duplex Mix Size NG016-941 Booklet
Duplex Mix Size NG016-942 Page Delete Duplex Mix Size NG 016-943
Insert doc Duplex Mix Size NG 016-944 Document merge NG 016-945
Insert doc Duplex print NG016-946 Insert doc NG016-947 APS No
Destination Error 016-948 Small Book action NG 016-949 Insert Mix
doc NG 016-981 HDD access error 016-982 HDD access error 2016-983
Image Log HDD Full 016-985 Data size over flow (Scan to
Email)017-700 ThinPrint Connection Timeout Fail017-701 017-701
ThinPrint Connection Fail017-702 017-702 ThinPrint Invalid Data
Fail 017-703 017-703 ThinPrint Over Maximum Data Size Fail 017-704
017-704 ThinPrint Internal Fail017-705 017-705 ThinPrint SSL
Authentication Invalid Certification Fail017-706 017-706 ThinPrint
SSL Authentication Before Expiration Fail 017-707 017-707 ThinPrint
SSL Authentication Expired Fail017-708 017-708 ThinPrint SSL
Authentication Misrepresentation Fail017-709 017-709 ThinPrint SSL
Fail017-710 017-710 SIP Mismatched Media Type Fail 017-711 017-711
SIP Redirect Response Fail017-712 017-712 SIP Session Timeout
Fail017-713 017-713 Start TLS Unsupported Fail 017-714 017-714 SMTP
Over SSL Fail -
Code Description017-715 017-715 SSL Cert Untrusted Fail 017-716
017-716 SSL Cert Date Invalid Fail017-717 017-717 SSL Server Cert
Expired Fail017-718 017-718 SSL Server Cert Invalid Fail017-719
017-719 SMTP Over SSL Internal Fail 017-720 017-720 Contract Type
Fail 017-721 017-721 Geographic Region Fail 017-722 017-722 Total
Impressions Over Fail 017-723 017-723 DocuWorks Unsupported
character Fail018-400 IPSEC Error (Configuration Mismatch) 018-401
Incosistent SIP configuration 018-402 SIP server communication
fail018-403 SIP registraion fail (authentication) 018-404 SIP
registration fail(other) 018-405 UserAccount Disable 018-500 CA
Message Receiver Boot Error(S_cert lost)018-501 CA Server
Connection Error018-502 Login failure in SMB018-503 CA Message
Receiver Timeout018-504 CA SessionID Mismatch018-505 SMB-DOS
protocol error 1-005018-506 CA FieldID Mismatch018-507 CA
Credential Error018-508 CA Server Fatal Error 018-509 Template
parameter conflict 018-510 Host name solution error in BMLinkS
018-511 DNS server un-sets up in BMLinkS018-512 Service Connect
error in BMLinkS 018-513 BMLinkS Service Not Found018-514 bmlinks
access-right-violation 018-515 bmlinks storage-access-error 018-516
bmlinks unsupported-attribute018-517 bmlinks storage-full 018-518
bmlinks operation-not-available018-519 bmlinks unknown-error
018-520 Internal error in BMLinkS Scan 018-521 request send failure
in BMLinkS 018-522 response receive failure in BMLinkS 018-523
image send failure in BMLinkS018-524 Invalid device network setting
018-525 HDD full or HDD access error 018-526 Rejected to be
refresh018-527 JT Monitor Internal error 018-528 Soap request error
018-529 Duplicate scan request018-530 Authentication error 018-531
Failed to create a new job 018-532 Too many jobs to create a
new018-543 Shared name error in SMB server -
Code Description018-547 The number restriction over of SMB scan
users018-556 HTTP server script error 018-557 HTTP Invalid char in
filename 018-558 HTTP file not found 018-559 HTTP File duplication
fail018-560 HTTP server login fail 018-561 HTTP server not
found018-562 HTTP client error018-563 HTTP server error 018-564
Host name solution error in HTTP018-565 Proxy name solution error
in HTTP018-566 Server Connect error in HTTP018-567 HTTP server
access fail018-568 HTTP server SSL access fail018-569 HTTP server
certificate fail 018-570 HTTP certificate fail 018-571 Internal
error in Scan 018-572 Invalid char in context 018-573 Invalid char
in server018-574 Invalid char in volume 018-575 Invalid char in
login018-576 Invalid char in path 018-577 Invalid char in file
018-578 Nw server not found018-579 Nw server disk full 018-580
Netware invalid volume 018-581 Netware invalid path 018-582 Access
right fail 018-583 Nw server disk error018-584 Nw server access
fail018-585 Netware error in use 018-586 Netware login fail 018-587
File duplication fail018-588 Scan filing policy invalid018-589
NEXTNAMEDAT error018-590 Same name exists 018-591 File name suffix
limit over 018-592 lock folder create fail018-593 lock folder
delete fail018-595 Detected user duplication, in LDAP018-596 LDAP
protocol error 596018-700 Network Stack is not Initialized
Fail018-701 LDAP protocol error 01 018-702 LDAP protocol error 02
018-703 LDAP protocol error 03 018-704 LDAP protocol error 04
018-705 LDAP protocol error 05 018-706 LDAP protocol error 06
018-707 LDAP protocol error 07 -
Code Description018-708 LDAP protocol error 08 018-709 Active
Communication is Unavailable Now Fail018-710 LDAP protocol error 10
018-711 LDAP protocol error 11 018-712 LDAP protocol error 12
018-713 LDAP protocol error 13 018-714 LDAP protocol error 14
018-716 LDAP protocol error 16 018-717 LDAP protocol error 17
018-718 LDAP protocol error18 018-719 LDAP protocol error 19
018-720 LDAP protocol error 20 018-721 LDAP protocol error 21
018-725 Kerberos Attestation protocol error 22 018-726 Kerberos
Attestation protocol error 70 018-727 Kerberos Attestation protocol
error 71 018-728 Kerberos Attestation protocol error 72 018-732
LDAP protocol error 32 018-733 LDAP protocol error 33 018-734 LDAP
protocol error 34 018-735 LDAP protocol error 35 018-736 LDAP
protocol error 36 018-748 LDAP protocol error 48 018-749 LDAP
protocol error 49 018-750 LDAP protocol error 50 018-751 LDAP
protocol error 51 018-752 LDAP protocol error 52 018-753 LDAP
protocol error 53 018-754 LDAP protocol error 54 018-764 LDAP
protocol error 64 018-765 LDAP protocol error 65 018-766 LDAP
protocol error 66 018-767 LDAP protocol error 67 018-768 LDAP
protocol error 68 018-769 LDAP protocol error 69 018-770 LDAP
protocol error 70 018-771 LDAP protocol error 71 018-780 LDAP
protocol error 80018-781 LDAP protocol error 81018-782 LDAP
protocol error 82018-783 LDAP protocol error 83018-784 LDAP
protocol error 84018-785 LDAP protocol error 85018-786 LDAP
protocol error 86018-787 LDAP protocol error 87018-788 LDAP
protocol error 88018-789 LDAP protocol error 89018-790 LDAP
protocol error 90018-791 LDAP protocol error 91 -
Code Description018-792 LDAP protocol error 92018-793 LDAP
protocol error 93018-794 LDAP protocol error 94018-795 LDAP
protocol error 95018-796 LDAP protocol error 96018-797 LDAP
protocol error 97021-210 USB IC Card Reader connection error021-211
USB IC Card Reader broken 021-212 USB IC Card Reader preparing
error021-213 Controller Price Table Error021-214 USB IC Card Reader
encryption setting error021-215 Invalid Accessory Kind
Setting021-360 EP Accessory Fail 021-361 EP Accessory Kind Config
Error021-400 Check Request021-401 USB IC Card Reader connection
error info021-500 EPAccessoryJobExclusion021-501 Invalid URL has
detected 021-502 Couldn’t resolve proxy name 021-503 Couldn’t
resolve host name021-504 Couldn’t connect to host/proxy 021-505
Couldn’t establish SSL session021-506 An invalid peer certificate
has received021-507 Proxy unauthorized access021-508 A connection
to host/proxy has timed out 021-509 SOAP Fault: An invalid message
detected021-510 SOAP Fault: The MC already unregistered021-511 SOAP
Fault: The MC already registered (WEP)021-512 SOAP Fault: The MC
already registered (EP-SV)021-513 SOAP Fault: The MC already
registered (EP-DX)021-514 SOAP Fault: The MC already registered
(EP-TRESS)021-515 SOAP Fault: An invalid product code
detected021-516 SOAP Fault: An invalid serial number
detected021-517 SOAP Fault: The service not responded 021-518 SOAP
Fault: An internal error occurred on server021-519 SOAP Fault:
Service is temporarily unavailable 021-520 Couldn’t connect to
CA021-521 A connection to CA has timed out021-522 A miscellaneous
CA comm error has detected021-523 An internal error has
occurred021-524 A registeration conflict has detected021-525 An
unregistration conflict has detected021-526 A miscellaneous http
session error has detected 021-527 An invalid message has received
021-528 A communication settings was set as disabled021-529 Device
has already latest firmware021-530 An internal error has occurred
on update server 021-531 Service is temporarily unavailable on
update svr 021-532 Found an unsupported ROM set -
Code Description021-533 Software Update unoperational by user
021-534 Found an unsupported submodule021-535 Found an unsupported
peripheral 021-700 Accessory Failure 021-701 Accessory
Preparing021-731 EP Accessory — Function Disabled021-732 EP
Accessory Error732021-733 EP Accessory Error733021-750 U Parts
Request Fail (EP-SV)021-751 Maintenance Request Fail (EP-SV)021-770
U Parts Request Fail (EP-DX)021-771 Maintenance Request Fail
(EP-DX)021-772 EPDX Install, Remove Error 021-941 EP — Scan Service
Paused By Disable021-942 EP — Scan Service Paused By Color
Mode021-943 EP — Print Service Paused By Disable 021-944 EP — Print
Service Paused By Color Mode021-945 EP — Service Paused By Disable
021-946 EP — Service Paused By Color Mode021-947 Subtractive
Accessory Disable (Scan) 021-948 Subtractive Accessory Disable
(Print)021-949 Subtractive Accessory Disable023-600 Held Down Key
Error(UI-Panel)023-601 Held Down Softkey Error(UI-Panel)024-340
IOT-ESS Communication Fail 1024-341 IOT-ESS Communication Fail
2024-342 IOT-ESS Communication Fail 3024-343 IOT-ESS Communication
Fail 4024-345 IOT-ESS Communication Fail 5024-346 IOT-ESS
Communication Fail 6024-347 IOT-ESS Communication Fail 7024-348
IOT-ESS Communication Fail 8024-349 IOT-ESS Communication Fail
9024-350 IOT-ESS Communication Fail 10024-351 IOT-ESS Communication
Fail 11024-352 IOT-ESS Communication Fail 12024-353 IOT-ESS
Communication Fail 13024-354 IOT-ESS Communication Fail 14024-355
IOT-ESS Communication Fail 15024-356 IOT-ESS Communication Fail
16024-357 IOT-ESS Communication Fail 17024-358 IOT-ESS
Communication Fail 18024-359 IOT-ESS Communication Fail 19024-360
IOT-ESS Initialization Fail 024-361 Invalid IOT PaperSizeGroup
Info024-362 Page Sync Illegal Start 024-363 Page Sync Illegal Stop
024-364 DMA Transfer Fail 024-365 Overflow on Loop Back Write -
Code Description024-366 JBIG Library Other Fail024-367
Decompress Other Fail 024-368 PCI Error024-370 Marker Code
Detection Fail024-371 IOT-ESSCommunication Fail 21024-372
IOT-ESSCommunication Fail 22024-373 IOT-ESSCommunication Fail
23024-374 Regi Con PLL Parameter Fail 024-375 IOT-ESSCommunication
Fail 24024-376 IOT-ESS Communication Fail 25024-600 Billing Master
Counter repair 024-601 Billing Backup Counter 1 repair024-602
Billing Backup Counter 2 repair024-603 SWKey Master Counter repair
024-604 SWKey Backup Counter 1 repair024-605 SWKey Backup Counter 2
repair024-606 Billing Meter Type Master Counter repaire024-607
Billing Meter Type Backup Counter 1 repaire024-608 Billing Meter
Type Backup Counter 2 repaire024-609 Billing CountType Master
Counter repaire 024-610 Billing CountType Backup Counter 1 repaire
024-611 Billing CountType Backup Counter 2 repaire 024-612 Modal
Break Point Master Counter repaire024-613 Modal Break Point Backup
Counter 1 repaire024-614 Modal Break Point Backup Counter 2
repaire024-700 Shortage memory capacity, or no Hard Disk 024-701
Invalid instruction of face inversion 024-702 Paper Jam024-703
Booklet Sheets Count Over While Printing Fail024-742 Print Booklet
sheets counts over 024-746 Print Request Failure-Paper 024-747
Print Instruction Fail024-748 Bates Numbering Digit Over 024-775
Print Booklet sheets counts over(Not field attachment)024-900 Upper
Tray Out Of Place 024-910 Tray1 size mismatch024-911 Tray2 size
mismatch024-912 Tray3 size mismatch024-913 Tray4 size
mismatch024-914 Tray6 size mismatch024-915 Tray7 size
mismatch024-916 Mix Full Stack 024-917 Stacker Tray Staple Set Over
Count 024-919 FaceUP Tray Close024-920 Face Down Tray1 Paper FULL
024-922 Face Down Tray2 Paper FULL 024-923 Operation Y Toner Empty
024-924 Operation M Toner Empty024-925 Operation C Toner Empty -
Code Description024-926 Punch DustBox Miss Set024-927 OCT Full
Stack024-928 Scratch Sheet Compile (A-Fin) 024-929 Center Tray Full
Stack 024-930 Stacker Tray Full (LargeSize Full) 024-931 Staple
Dust Full024-932 Staple Box Set Fail 024-933 Operation Y Drum End
of Life024-934 Paper kind mismatch024-936 Tray 2 paper mismatch
024-937 Tray 3 paper mismatch 024-938 OHP kind mismatch at Tray4
(Not white frame OHP)024-939 OHP kind mismatch (Not white frame
OHP) 024-940 Folder Tray Out Of Place024-941 Folder Tray Full
Stack024-942 Booklet sheets counts over024-943 Booklet Low Staple
024-945 Booklet Full Stack 024-946 Tray 1 Out Of Place024-947 Tray
2 Out Of Place024-948 Tray 3 Out Of Place024-949 Tray 4 Out Of
Place024-950 Tray 1 Empty 024-951 Tray 2 Empty 024-952 Tray 3 Empty
024-953 Tray 4 Empty 024-954 Tray SMH Empty 024-955 Tray 6 Empty
024-956 Tray 7 Empty 024-957 Interposer Empty 024-958 SMH size
mismatch024-959 Tray1 size mismatch024-960 Tray2 size
mismatch024-961 Tray3 size mismatch024-962 Tray4 size
mismatch024-963 Finisher Punch DustBox FULL024-965 ATS/APS No Paper
(IOTsc detect)024-966 ATS/APS No Destination Error 024-967
Different width Mix Paper detect (Stapler job)024-968 Stapler/Punch
Batting 024-969 Different width Mix Punch 024-970 Tray 6 Out Of
Place024-971 Tray 7 Out Of Place024-972 Tray6 size mismatch024-973
Tray7 size mismatch024-974 Interposer Tray Size Mismatch 024-975
Copy Booklet sheets counts over 024-976 Finisher Staple Status
NG024-977 Stapler Feed Ready Fail -
Code Description024-978 Booklet Stapler NG 024-979 Stapler Near
Empty024-980 Finisher Stacker Tray Full 024-981 Finisher TopTray
Full024-982 Stacker Lower Safety warning 024-983 Booklet Tray
Full024-984 Booklet Low Staple F024-985 SMH Stop check024-987
Envelop Folder Tray Full024-988 Envelop Folder Tray Set Fail
024-989 Booklet Low Staple R 024-990 Punch Dust Full 025-596 Diag
HDD Mentenance Fail025-597 Diag HDD Initialize Fail 026-400 Exceed
the number of connection of USB Host Fail026-700 LDAP protocol MAX
error 026-701 Adress Book request overflow 026-702 Adress Book
directory service overflow026-703 Abort with Logout026-704
DocuWorks Error 026-705 DocuWorks Short of Memory026-706 DocuWorks
Print Prohibited026-707 DocuWorks Unlock Failed026-708 URL data
size over026-709 URL hdd full026-710 S/MIME unsupported cipher
decrypt fail026-711 Multi-page file size over026-712 HTTP out job
overlap error026-713 Couldnt detect proxy server automatically
026-714 Couldnt connect to Xerox server or proxy026-715 Connection
to Xerox server has timed out 026-716 An invalid state message
received from server026-717 Invalid network settings were
found026-718 PS Print Instruction Fail026-719 Internal error in
Scan 026-720 Media full 026-721 Media access fail 026-722 Media
format fail 026-723 Media access fail 026-724 Remote Download file
size error026-725 Remote Download file checksum error 026-726
Options inconsistent 026-727 Media filepath fail026-728 WSD Scan
Network Access Fail026-729 WSD Scan Data Transfer Fail026-730 Can’t
Detect Paper Size Of Specified Tray 026-731 PJL PIN Number
Fail026-732 PJL Printcount Range Over Fail 026-733 PJL Password
Fail -
Code Description026-734 Can not change to the PJLDIAG MODE
026-735 Authentication Makes Waiting Print Jobs Deleted027-400 Net
Off Line 027-442 Duplicat IP address 027-443 DNS renewal failure of
dynamic 027-444 Duplicat IP address 027-445 Illegal IP address
027-446 Duplicat IP address 027-447 Duplicat IP address 027-452
Duplicat IP address 027-500 SMTP Server Fail for Mail IO027-501 POP
Server Fail for Mail IO027-502 POP Authentication Fail for Mail
IO027-503 POP server communication timeout 027-504 Response
reception is not expected from server 027-513 SMB Scan client has
no right to access 027-514 Host name solution error in SMB027-515
DNS server un-sets up in SMB 027-516 Server connection error in
SMB027-518 Login name or a password error in SMB 027-519 Scanning
picture preservation place error in SMB027-520 File name
acquisition failure from SMB server027-521 File name suffix limit
over in SMB 027-522 File creation failure in SMB 027-523 Lock
folder creation failure in SMB 027-524 Folder creation failure in
SMB027-525 File delete failure in SMB027-526 Lock folder delete
failure in SMB027-527 Folder delete failure in SMB 027-528 Data
write-in failure to SMB server 027-529 Data read failure from SMB
server027-530 File name duplicate failure in SMB027-531 SMB scan
filing policy injustice 027-532 NEXTNAMEDAT file access error in
SMB027-533 Internal error in SMB Scan027-543 SMB server name
specification error027-547 SMB Protocol error 4-007 027-548 SMB
Protocol error 4-008 027-549 SMB Protocol error 4-009 027-564 SMB
Protocol error 4-024 027-565 SMB Protocol error 4-025 027-566 SMB
Protocol error 4-026 027-569 SMB (TCP/IP)is not started027-572 SMB
Protocol error 4-032 027-573 SMB Protocol error 4-033 027-574 SMB
Protocol error 4-034 027-576 SMB Protocol error 4-036 027-578 SMB
Protocol error 4-038 027-584 SMB Protocol error 4-044 -
Code Description027-585 SMB Protocol error 4-045 027-586 SMB
Protocol error 4-046 027-587 SMB Protocol error 4-047 027-588 SMB
Protocol error 4-048 027-589 SMB Protocol error 4-049 027-590 SMB
Protocol error 4-050 027-591 SMB Protocol error 4-051 027-599 SMB
Protocol error 4-other 027-600 ExtPrint Check Mode Error027-700
Mail address domain err 027-701 Disconnect network cable 027-702
Certificate for addresses, was not found 027-703 Certificate for
addresses, was expired 027-704 Certificate for addresses, was
untrusted 027-705 Certificate for addresses, was revoked 027-706
Certificate not found027-707 Certificate expired 027-708
Certificate untrusted027-709 Certificate revoked 027-710 S/MIME
mail was disabled 027-711 S/MIME mail sender certificate not found
027-712 S/MIME mail sender certificate not valid027-713 S/MIME mail
was altered 027-714 S/MIME mail sender impersonation027-715 S/MIME
mail certficate not support 027-716 No-Signed mail receipt was
rejected 027-717 No MX Record at the DNS 027-720 Ext Srv Host Not
Found 027-721 Ext Srv Not Found027-722 Ext Srv Timeout Fail027-723
Ext Srv Authentication Fail 027-724 Ext Srv Access Fail027-725 Ext
Srv Operation Fail 027-726 Ext Srv Unknown State027-727 Ext Srv Req
Invalid Params027-728 Ext Srv Req File Exceed027-730 SMTP mail
division error 027-731 Server Limit Err 027-732 Server Access Err
027-733 Server SSL Err027-734 Server Certificate Err027-735 Device
SSL Config Err 027-736 Device Certificate Err027-737 Template
Server Read ERR027-739 Invalid Template Server Path 027-740
Template Server Login ERR027-741 Template Server Connect Fail
027-742 HD File System Full027-743 Template Server Install ERR -
Code Description027-744 Template Server ADD ERR (DNS Library)
027-745 Template Server ADD ERR (DNS address)027-746 JobTemplate
Pool Server Not Ready 027-750 Fax document incongruent 027-751 Job
Template analysis error 027-752 Must user un inputting027-753 Job
flow service request disabled 027-754 Job flow service File
signature setting mismatch 027-760 XJT Command Fail 027-761 Web
Print time out 027-762 Illegal Web Print job ticket027-763 Auditron
— Cannot Verify User 027-770 PDL Error027-771 DFE Disk Full027-772
SMTP server error (HELO Command refusal)027-773 SMTP server
communication timeout 027-774 SMTP address inaccurate character
027-775 Too many SMTP address 027-776 SMTP server error (EHLO
Command refusal)027-777 SMTP server un-supports SMTP-AUTH027-778
There is no mode specified by SMTP-AUTH027-779 It attestation-fails
by SMTP-AUTH 027-796 Email Not Printed027-797 Invalid Output
Destination027-910 Manual duplex operation(Back Print from
Tray7)027-911 Manual duplex(Back Print from Tray6) 027-912 Manual
duplex(Back Print from Tray5) 027-913 Manual duplex(Back Recovery —
Front Print)027-914 Manual duplex(Back Recovery — Front
Print)027-915 Manual duplex(Back Recovery — Front Print)027-916
Manual duplex(Back Recovery — Back Print)027-917 Manual duplex(Back
Recovery — Back Print)027-918 Manual duplex(Back Recovery — Back
Print)028-910 Wrong Fusing Unit Type Fail028-911 Wrong Fusing Unit
Mode Fail028-912 Fusing Unit Lever Envelope Fail033-310 Fax Charge
Function Fail By Multi Channel033-311 Invalid Addressbook Data are
Registered033-312 Controller not respond when system is changing
mode033-313 USB disconnected033-314 Controller ROM Fax Card ROM
mismatch033-315 USB Fatal Error033-316 FAX Device Cont Error033-317
FAX Device Error033-318 Image Processing Error033-319 Fax Control
task detects error033-320 Controller not respond when system is
Booting033-321 Fax Card not respond when system is Booting033-322
FAX Card I/F timeout -
Code Description033-323 FAX Card Mini I/F timeout033-324 USB
state change Error033-325 FCM Fatal Error033-326 Mini Manager Fatal
Error033-327 FCM no response to stop request033-328 Failed to
initialize fax log033-329 Detected fax process failuer033-330 FoIP
Unrecoverable Error033-331 FoIP Controller Init Fail033-332 FoIP
Cont not respond when system is Booting033-333 FoIP Cont not
respond when system is sleeping033-334 Can not send a message to
FoIP CONT033-335 Illegal fault code notice033-336 Access to a
non-mounted channel033-337 FaxCard mismatch033-338 Illegal type of
FaxBox033-339 faxc2 not respond when system is sleeping033-363 Fax
Card Reset (Reboot)033-500 No CS after RS Req033-501 No Appropriate
PIX Data033-502 Post-message resend exceeded033-503 T1
Timeout033-504 T2 Timeout033-505 T5 Timeout033-506 DCN
Receive033-507 Unable to receive by remote033-508 Destination
Polling Error033-509 DCS/NSS Resend Exceeded033-510 Fallback
Error033-511 No response after 3rd DTC/NSC033-512 Remote has no
Relay033-513 Remote has no Mailbox033-514 Carrier Down
Detected033-516 EOR Receive033-517 ECM Phase C Flag Timeout033-518
Remote cannot receive SUB033-519 PTX has no SEP capability033-520
Remote cannot receive passward033-521 Transmission Canceled via
DTMF033-522 DTMF I/F Timeout033-523 Line 1 not connected033-524
Line 2 not connected033-525 Line 3 not connected033-526 ECM
Error033-527 EOR Send033-528 RTN Send033-529 RTN Receive033-530
DTMF Illegal Procedure Error033-531 DTMF Procedure Error -
Code Description033-532 Illegal Command Received033-533 T30
Protocol Error033-534 Unsupported Function at Remote033-535 DCN
Receive at Phase B Send033-536 Ring Stopped before Fax Device
Release033-537 In and out call conflict033-538 Fax Sending Image
Process Error033-539 Fax Receiving Image Process Error033-540 Fax
Printing Image Process Error033-541 No destination specified033-542
Selected Channel Dial Error033-543 Dial Error (Incorrect Dial
Data)033-544 Busy tone detect033-545 T0 Timeout033-546 Cannot
detect dial tone033-547 Abort during transmission033-548 No manual
send line033-549 Fax service disabled033-550 cannot diable FAX
service033-551 Internal I/F Error033-552 too many Error
lines033-553 no mailbox/relay033-554 Wrong Password/Receive
Banned033-555 incorrect password033-556 Wrong Password/Send
Banned033-557 Desinations or Sevices Exceeded033-558 remote ID is
in black list033-559 no remote ID033-560 illegal authentication
ID033-561 cannot do TRESS/RCC job033-562 held RCC job033-563 No
printable paper size033-564 Power Off during transmission033-565 No
of Desinations Exceeded033-566 No destination specified033-567 Dial
Error (Incorrect Dial Data)033-568 FCM watchdog timeout in FAX
comm033-569 Detected image direction conflict033-570 Retry Over(no
shutdown notification setting)033-571 Manual send job
canceled(FaxReportLogFull)033-572 FaxReport print job
canceled(JobFull occured)033-573 domain regulation check
error033-574 Access to a non-mounted channel033-575 Modem Polarity
Inversion Detected033-576 Inaccurate dial data033-577 Modem Image
Under Run033-578 Modem Frame Size Over033-580 Missing VoIP
Gateway033-581 Access Authentication failure -
Code Description033-582 Mismatched ability033-583 Temporarily
unavailable033-584 SIP request timeout033-585 SIP request
error033-586 T38 Protocol Not Ready033-587 T38 Session Error033-588
T38 Packet Lost033-589 T38 Malformed Packet Received033-590 T38
Send Error033-591 FoIP Max Sessions Over033-592 FoIP Internal
Timeout033-593 Canceled By Remote Peer033-710 Document does not
exist033-711 Illegal Page inside Document033-712 System Memory
exceeded033-713 No specified Chain Link033-714 Scan Error (No
specified doc)033-715 Cannot start job033-716 No specified
Mailbox033-717 Incorrect Password033-718 No Document in
Mailbox033-719 Fax job Canceld not recovery job033-720 Document
Creation Failed033-721 Fax Page Creation Failed033-722 Fax
immediate send store job canceled033-724 Fax receive memory over
flow033-725 Insufficient HDD Space033-726 Cannot print
2-Sided033-727 Cannot rotate image033-728 Auto print
canceled033-730 Fax Service recovery error033-731 Inconsistent
Instructions033-732 Print job canceled by forced polling033-733 Fax
document number get error033-734 Fax Print Suspension033-735 Fax
Memory Allocate Timeout033-736 Internet FAX Off Ramp fail033-737
Fax card job canceled033-738 JBIG Information fail033-740 Fax
immediate receive print canceled033-741 Fax page read open
timeout033-742 Fax page read close timeout033-743 Fax page write
open timeout033-744 Fax page write close timeout033-745 Fax data
write timeout033-746 Fax data read timeout033-747 Fax Service don’t
start by cross ope033-748 Fax Service illigal sequence033-749 Fax
card Memory Error -
Code Description033-750 Fax format error033-751 Activity Report
suspended by Printing Inhibition033-755 Fax printing is canceled by
the defect of Fax card033-790 EP-DX Call Wait (Not Redial
count)033-791 EP-DX Call Wait (Redial count)033-792 EP-DX Call
Stop034-211 Slot1 Board failure034-212 Slot2 Board failure034-500
Dial Error (Incorrect Dial Data)034-501 Selected Channel Dial
Error034-502 Fax Internal Must Parameter Error034-503 Fax Internal
High Layer Service Error034-504 Fax Stored Memory Exceeded034-505
Fax Work Memory Exceeded034-506 Unsupported Function at
Remote034-507 Password Check Error034-508 Transmission Canceled via
DTMF034-509 DTMF Illegal Procedure Error034-510 DTMF Procedure
Error034-511 Unable to Send File at Remote034-512 Detect Endless
Loop034-513 Receive Command Error034-514 Requested Function
Unsupported034-515 Illegal Command Received034-519 No of
Desinations Exceeded034-520 No of Sevices Exceeded034-521 Internal
I/F Error034-522 No manual send Line034-523 Fax service
disabled034-524 Unable to cancel operation034-525 Specified
Chainlink not exist034-526 Chainlink No out of scope034-527 Dial
Control Error034-528 Cannot perform manual send034-529 No printable
paper size034-530 DTMF I/F Timeout034-550 Downloader Fail034-700
GCPLock-G3DicepBusy-CodecHang034-701 Software Reset034-702 No
destination specified034-703 D Channellink cut from network034-704
ISDN D Channel Data Link Error034-705 ISDN Layer 1 Stopped-Power
on034-706 ISDN Layer 1 Stopped-Power off034-707 FRMR
Received034-708 Illegal Frame Received N(R)034-709 Illegal Frame
Received034-710 DL Link Establishment Received034-711 Waiting for
link Timeout -
Code Description034-712 Internal Error (Interrupt)034-713
Timeout-Transmission canceled034-714 Line Disconnected-Timeout
T305034-715 Line Disconnected-Timeout 3082034-716 Connection
Timeout (T313)034-717 Resume Timeout034-718 Normal
Disconnection034-719 No free and available lines034-720 Timeout
(60s,T330,309,301,310)»034-721 Error (Format, Contents) «034-722
Suspension Timeout034-723 No Timer Assigned034-724 Illegal
Sequence034-725 L3 Task Internal Error034-726 HD81501 I/F Buffer
Busy034-727 No Reply for 3 sec for 1300Hz034-728 Invalid
Destination034-729 Line cut, In-Channel PB Send»034-730 In and out
call conflict034-731 Fax Network Cut (Setup Error)034-732 Fax
Network Cut due to Timeout034-733 Incorrect Sequence,Call
Status»034-734 HI Task Internal Error034-735 Connect only to ISDN D
Channel034-736 Wrong notice from fax network034-737 Incoming call
response error034-738 Layer 1 Start Up Error034-739 Layer 1 not
synchronized034-740 Transmission of Frame Error034-741 Unable to
Send Frame034-742 Frame Send Underrun Detected034-743 Abnormal
frame-sending DMA034-744 Unacceptable Channel034-745 Outgoing call
to channel set034-746 No usable lines034-747 Switching equipment
congestion034-748 Specified line cannot be used034-749 Network
Conjestion Error034-750 Network Error034-751 Temporary Network
Error034-752 Destination terminal busy034-753 Destination not
responding034-754 No response from Destination034-755 Destination
rejecting call034-756 Destination Faulty034-757 Others (Normal,
Semi-normal) «034-758 Incorrect Destination Fax Dial No034-759 No
Relay Network Route034-760 No Line To Destination -
Code Description034-761 Incorrect Format Destination Fax
No034-762 Facility rejected034-763 Com Capability disallowed034-764
Com Capability not configured034-765 Error by service,feature limit
«034-766 Selected com not implemented034-767 Selected mode not
implemented034-768 Restricted Digital Info Only034-769 Error by
service, feature»034-770 Reply to status query034-771 Access
information discarded034-772 Inter-working connection error034-773
Invalid Dial No Specified034-774 Invalid Line Specified034-775
Others (Invalid Message Class)034-776 Insufficient Required
Info034-777 Undefined Message Type034-778 Incorrect Message or
Type034-779 No information, or not defined»034-780 Invalid
Information034-781 Call Status, Message Mismatch»034-782 Error
cleared due to timeout034-783 Other Errors (Operation, etc)
«034-784 Destination No Changed034-785 Incompatible
destination034-786 Call identity not in use034-787 Call identity in
use034-788 Show other causes034-789 G4 Presentation Illegal
Event034-790 Line 0 (Ext) not connected034-791 Line 1 not
connected034-792 Line 2 not connected034-793 Line 3 not
connected034-794 Line 4 not connected034-795 Line 5 not
connected034-796 Dial Error (Incorrect Fax No 2)034-797
Communication Parameter Error034-798 Data Parameter Error034-799
Auto Dial without dial data035-550 Downloader Fail035-700 Modem
faulty035-701 T1 Transmission Timeout035-702 Destination Receive
Rejected035-703 DCN Receive at Phase B Send035-704 Destination
Polling Error035-705 DCS/NSS Resend Exceeded035-706 Fallback
Error035-707 Wrong Password/Receive Banned035-708 Post-message
resend exceeded -
Code Description035-709 RTN Receive035-710 PIN Receive035-711
DCN Receive at Phase D035-712 No response after 3 NSC035-713 T2
timeout after sending FTT035-714 DCN Received after NSC/DTC035-715
Wrong Password-Polling Error035-716 No past message-T2
Timeout035-717 RTN Send035-718 Receive T1 Timeout035-719 Busy tone
detected at Phase-B035-720 Unable to receive by remote035-721 DCN
Received at Phase B035-722 Wrong frame length of 300bps035-723 No
CD after receiving flag035-724 DCN Receive after sending FTT035-725
Remote has no Mailbox/Relay035-726 PhaseC cannot receive-10
secs035-727 50% Error during G3 Receive035-728 C EOL cannot receive
in 10 sec035-729 Carrier Down Detected035-730 No CS with Phase-C
High Speed035-731 Fax V8 Error035-732 Fax V34 PCH CD Off035-733 Fax
V34 C/PCH CS None035-734 Polling ERR at Remote Step V8035-735 No
Doc in Polling Box Step V8035-736 No reply DCN after sending
CTC035-737 No reply DCN after sending EOR035-738 No reply DCN after
sending RR035-739 Fax T5 Timeout035-740 Sending stopped after EOR
Send035-741 ECM Phase C Flag Timeout035-742 EOR Send or
Receive035-743 Remote cannot receive SUB035-744 Remote cannot
receive password035-745 PTX has no SEP capability035-746
Busy-Cannot detect dial tone035-747 Abort while dialing035-748
Abort during transmission035-749 No reply from remote
station035-750 Power Off during transmission035-751 Doc send
operation canceled035-752 No of Job Restriction Error035-753 Fax
Memory Full035-754 File management memory full035-755 File Add Page
Error035-756 Cannot add page035-757 No Receive Page -
Code Description035-758 No specified file or page035-759 No
specified job035-760 File common processing error035-761 File other
processing error035-762 Line cut during ISDN036-500 Illegal PDRP
Parameter036-501 Illegal RDPBP Parameter036-502 Illegal RDPBN
Parameter036-503 Illegal RDCLP Parameter036-504 Illegal RDGR
Parameter036-505 Undefined response036-506 Not negotiable036-507
RDPBP Receive at full capacity036-508 RDPBN Receive Terminal
Error036-509 RDPBN Receive Others036-510 RDGR Receive036-511
Illegal procedure 1551036-512 Illegal CDS Parameter036-513 Illegal
CDC Parameter036-514 Illegal CDE Parameter036-515 Illegal CDD
Parameter036-516 Illegal CDR Parameter036-517 Illegal CDPB
Parameter036-518 Illegal CDCL Parameter036-519 Undefined
Command036-520 Not Negotiable CDS Receive036-521 Not Negotiable CDC
Receive036-522 CDD Receive Terminal Error036-523 Other than above
CDD receive036-524 CDR Receive Terminal Error036-525 Other than
above CDR receive036-526 Illegal CDUI (Normal Doc)036-527 Illegal
CDUI (Operator Doc)036-528 Illegal CDUI (Control Doc)036-529
Illegal CDUI (Monitor Doc)036-530 CDSReceive-Illegal
Document036-531 DMA channel 1 illegal closing036-532 DMA channel 2
illegal closing036-533 Cannot convert resources036-534 Decode Error
in Data Convert036-535 White Line Transfer Error (Compress)036-536
White Line Transfer Error (Decomp)036-537 No RTC during data
convert036-538 Doc descriptor analysis error036-539 Page Descriptor
Analysis Error036-540 Text Unit Analysis Error036-541 Page boundary
without TU036-542 Relay Broadcast error in G4036-550 Downloader
Fail -
Code Description036-700 G4 Communication Error036-701 Receiving
variable N(R) error036-702 Info frame size exceeded (NI)036-703
Monitor/Unnumbered frame error036-704 Undefined Command/Response
1104036-705 N2 timeout of Receive Timer036-706 SABM Wait Timeout in
G4036-707 UA wait Timeout in G4036-708 Cannot establish link in
G4036-709 DISC receive before link close036-710 FRMR Receive
(Z=1)036-711 FRMR Receive (Y=1)036-712 FRMR received (Z=1)
W=1036-713 FRMR Receive (W=1)036-714 Global Address Receive036-715
Line Open Timeout in G4036-716 Wrong LSI Send (Busy Timeout)036-717
Abnormal LSI operation036-718 Disconnection Notice Timeout036-719 C
Line On but I Line Off036-720 C Line Off but I Line On036-721 I
Line Off during Transmission036-722 Call cut during flag
detect036-723 Call cut while awaiting UA036-724 Call cut while
awaiting SABM036-725 Disc received before session036-726 Illegal
header received036-727 Illegal parameter of CC packet036-728
Illegal parameter of CN packet036-729 Illegal parameter of DT
packet036-730 Illegal parameter of RI packet036-731 Illegal
parameter of IT packet036-732 Illegal parameter of CI packet036-733
Illegal parameter of CF packet036-734 Undefined Packet
Received036-735 CC Wait Timeout036-736 CF Wait Timeout036-737 CI
received before G4 session036-738 DT Packet P(S ), P(R )
Error»036-739 RR, RNR Packet P(S) Error «036-740 Busy
Timeout036-741 SI received in transmission036-742 SF received in
transmission036-743 DT Packet D Bit Error036-744 G4 Wait for Reply
Timeout036-745 G4 CN Wait Timeout036-746 G4 Data Link Disconnect
Notice Timeout036-747 Fast select response received036-748 Receive
remote charge request -
Code Description036-749 Abnormal LCGN036-750 Illegal procedure
1301036-751 Illegal TCA Parameter036-752 Illegal TCR
Parameter036-753 Illegal TCC Parameter036-754 Illegal TBR
Parameter036-755 Illegal TDT Parameter036-756 Undefined transport
block036-757 TCA Wait Timeout036-758 TCR Wait Timeout036-759 TCC
Wait Timeout036-760 TBR Wait Timeout036-761 TDT block size
error036-762 G4 NetWork Disconnect Notice Timeout036-763 Illegal
procedure 1401036-764 Illegal CSS Parameter036-765 Illegal CSE
Parameter036-766 Illegal CSA Parameter036-767 Illegal CSUI
Parameter036-768 Illegal CSCC Parameter036-769 Illegal RSSP
Parameter036-770 Illegal RSSN Parameter036-771 Illegal RSEP
Parameter036-772 Illegal RSAP Parameter036-773 Illegal RSUI
Parameter036-774 Illegal RSCCP Parameter036-775 Undefined
command/response 1413036-776 RSSN Receive036-777 G4 Line Disconnect
Notice Timeout036-778 CSA received (wrong terminal)036-779 CSA
Receive (Others)036-780 CSS Wait Timeout036-781 RSSP Wait
Timeout036-782 RSAP Wait Timeout036-783 RSEP Wait Timeout036-784
RSCCP Wait Timeout036-785 CSUI/RSUI Wait Timeout036-786 Incorrect
Password (RSSN)036-787 Wrong Password-Polling Error for
Remote036-788 Poll Send Error at Remote036-789 No Password for RSSP
Receive036-790 Polling rejected by remote036-791 Set Password-RSSP
Received036-792 CSE Received after RSSP Send036-793 Select
communication error036-794 Line cut during ISDN mode036-795
Canceled by remote station036-796 Sent without multiple sets036-797
Illegal procedure 1501 -
Code Description036-798 Illegal RDEP Parameter036-799 Illegal
RDDP Parameter041-500 Write to IOT-ROM error detection (During DLD
method)041-501 Write to IOT-NVM-ROM error detection (During DLD
method)048-500 IF-Module ROM Write Error049-500 HCS1 ROM Write
Error049-700 Out tray changed from stacker1049-950 HCS1 MIX SIZE
STACK Fail049-973 Stacker Extraction button was pushed062-394 Cont
PWBA Memory Fail062-500 Write to IISS-ROM error detection (During
DLD method)062-790 Possible Prohibited Originals063-500 Write to
IISS-Extension-ROM error detection (During DLD method)071-940
Tray#1 LiftUp NG072-940 Tray#2/TTM#2 LiftUp NG073-940 Tray#3/TTM#3
LiftUp NG074-940 Tray#4 LiftUp NG077-911 Paper size mismatch, job
contniue»077-967 Paper kind mismatch (APS job)077-968 Paper kind
mismatch, job contniue «078-500 Write to HCF-ROM error detection
(During DLD method)078-940 2000A3-HCF paper misset078-941
2000A3-HCF size mismatch078-942 4000A3HCF lower tray paper
misset078-943 4000A3HCF lower tray size mismatch093-434 Drum/Toner
Cartridge K Near Empty093-435 Drum/Toner Cartridge Quality
Empty093-940 Toner Y CRUM Comm Fail102-356 EWS Soft Fail102-380 MF
UI cont Soft Fatal error102-381 Data Link Layer Error
(UI-Panel)102-382 Application Layer Command Error (UI-Panel)103-310
Hybrid Water Mark Not Exist103-311 Hybrid Water Mark Setting
Mismatch103-312 Hybrid Water Mark Not Exist (Back Side)103-313 SW
Option Fail (IISS Mem for HWM Not Exist)112-700 Punch Dust Near
Full116-210 MediaReader Faital Error116-211 MediaReader Cable No
Joint116-212 MediaLib SW Logic Fail116-220 Transition to Download
Mode Download Initialization Failure116-310 ESS Font ROM DIMM #2
Check Fail116-311 ESS Font ROM DIMM #3 Check Fail116-312 HDD
Encrypt Key Fail116-313 HDD Encrypt Set Up Fail116-314 Ethernet
Address Fail116-315 ESS RAM DIMM #1 W/R Check Fail116-316 ESS RAM
DIMM #2 W/R Check Fail116-317 Standard ROM DIMM Check Fail -
Code Description116-318 Op ROM DIMM Check Fail116-319 Mismatch
Cont ROM and Panel config116-320 STREAMZ Soft Fatal error116-321
System Soft Fatal error116-322 WebDAV S/W Fail116-323 ESS NVRAM W/R
Check Fail116-324 Exception Fail116-325 ESS Fan Fail116-328 L2
Cache Fail116-329 Serial IF Soft Fail116-330 HDD File System
Fail116-331 Invalid Log Info116-332 ESS Standard ROM Error116-333
LocalTalk Soft Fail116-334 ESS NVRAM Data Compare Fail116-336
Redirector HD Fail116-337 SNTP S/W Fail116-338 JBA fatal
error116-339 JBA No HD116-340 Memory Not Enough116-341 ROM VER
Incorrect116-342 SESAMi Manager Fail116-343 Main PWBA IC
Fail116-345 TokenRing Board Fail116-346 Formatter Fail116-347
LocaTalk Board Fail116-348 Redirecter Fail116-349 SIF Fail to Call
Pflite116-350 AppleTalk Soft Fail116-351 EtherTalk Soft Fail116-352
NetWare Soft Fail116-353 HDD Phisycal Fail116-354 HDD Product
Fail116-355 Agent Soft Fail116-356 HDD Format Fail116-357
PostScript Error116-358 Salutation Soft Fail116-359 PLW Soft
Fail116-360 SMB Soft Fail116-361 Spool Fatal HDD116-362 SSDP Soft
Fail116-363 BMLinkS/Print Service Soft Fail116-364 Timer
Fail116-365 Spool Fatal116-366 Report Gen Soft Fail116-367 Parallel
IF Soft Fail116-368 Dump Print Fail116-370 XJCL Fail116-371 PCL
Decomp S/W Fail -
Code Description116-372 P-Formatter Fail116-373 Dynamic DNS Soft
Fail116-374 Auto Switch Fail116-375 I-Formatter Fail116-376 Port
9100 Software Fail116-377 Video DMA Fail116-378 MCR Soft
Fail116-379 MCC Soft Fail116-380 ESS Font ROM DIMM #1 Check
Fail116-381 ABL Initialize Fail116-382 ABL Phisycal Initialize
Fail116-383 PIT Lib Failure116-384 DCS Software Fail116-385 IDC
Software Fail116-386 Incorrect USB port used for FAX116-387 MRC HW
Fatal Error116-388 No HD that Should Be116-389 No Add-On RAM that
Should Be116-390 Standard ROM and NVM Version Mismatch116-391
Illegal code (country/territory/size group)116-392 Machine Code
Check Fail116-393 AAA Manager S/W Fail116-394 AAA Manager detect
illegal setting Auth & Acct116-395 USB Soft Fail116-396 FIPS140
Self-Test Fail116-397 AAAmgr illegal setting area coverage
threshold116-399 MUnder initialization for 10 minutes116-700 Image
Extension Kit Insufficient Memory116-701 Out of Memory-Duplex
Fail116-702 Print with Substitute Font116-703 PostScript LANG
Interprete ERR116-704 MediaReaderMedia No Insert(No Job)116-705
MediaReader Format Error(No Job)116-706 MediaReader:File Attribute
Read Error(No Job)116-707 MediaReader:Image File Read Error(No
Job)116-708 MediaReader:File Attribute Read Error(In Job)116-709
MediaReader:Image File Read Error(In Job)116-710 HP-GL/2 Memory
Overflow116-711 PLW Size/orientation mismatch116-712 Out of
Area-Form REGI ERR116-713 Job divided by HDD Full116-714 HP-GL/2
Command ERR116-715 Max Form to PLW Registered116-716 MediaReader
File Not Exist116-717 MediaLib:Not Excecute of New Request116-718
Selected PLW Form Not Registered116-719 XPIF Parameter
Cancelled116-720 PCL Memory Low,Page Simplified»116-725 HDD full
for Image Log -
Code Description116-737 Out of Area-Data REGI ERR116-738
Size/orientation mismatch116-739 Out of Disk Area-Form/Logo REGI
ERR116-740 Arithmetic Error116-741 Max Form to Not PLW
Registered116-742 Max Logo Registered116-743 Out of Buffer
Area-Form/Logo REGI ERR116-745 ART Command ERR116-746 Selected Form
Not Registered116-747 Invalid Page Margin116-748 Page without Image
Draw Data116-749 PostScript Font error116-751 HDD Full
Warning116-752 Print job ticket description warning116-771 Invalid
JBIG Param DL Fixed116-772 Invalid JBIG Param D Fixed116-773
Invalid JBIG Param P Fixed116-774 Invalid JBIG Param YD
Fixed116-775 Invalid JBIG Param L0 Fixed116-776 Invalid JBIG Param
MX Fixed116-777 Invalid JBIG Param MY Fixed116-778 Invalid JBIG Par
VLENGTH Fixed116-780 Attached Document Error116-790 Stapling
Canceled117-310 WSD Scan S/W Fail117-311 Wrong insertion of
security enhancing kit117-312 Device Self Test Error117-316
Contract Manager Software Fail117-317 Contract Manager PPP_contract
Finishing Fail117-318 Contract Manager PPP DC Command Fail117-319
SD Card Program or Font Data Access Fail117-320 SD Card HW
Fail117-321 SD Card Invalid Type Fail117-322 SD Card Encrypt
Fail117-323 SD Card File Access Fail117-324 SD Card Other Product
Fail117-325 Contract Manager RTC Hardware Fail117-326 ESS NVRAM SW
Access Fail117-327 ESS NVRAM (SD Card) HW Access Fail117-328 Detect
invalid combination of function for image log Fail117-329 SD Card
Not Found Fail118-310 IPSEC Intenal Fail121-310 EPSV-Accessory
Communication Fail121-311 IC Card Auditron Passwd Fail121-312 IC
Card Auditron Accessory Fail121-313 IC Card Auditron Software-key
Fail121-314 Customize User Prompts Fail121-316 EP Accessory
conflicts with SecureAccess121-317 Continuous JOB setting missmatch
of EPLyzer -
Code Description121-318 Auth/Accout Settings Is Not
Supported121-319 Fax Send Charging and Internet FAX Setting
Confliction121-320 EP-SV Setting information conflict fail121-321
EP-DX Setting information conflict fail121-322 Controller Price
Table Error121-323 Web EP Software Fail121-324 Fax Send Charging
And Scan Setting Confliction121-333 EPSV-EP M/C Communication
Fail121-334 EPSV Login Fail121-335 EPSV Wake Up Answer Fail121-336
Unknown EP Accessory121-337 EP Accessory Self Diag Fail121-338 EPSV
Answer Time Out121-339 Price Table Error121-340 EP Accessory Miss
Match121-350 EPSV Logic Fail121-370 EP-DX — unexpected error123-207
Comm Manager Target Fail (UI-Panel)123-209 EVM Returns Wrong Value
(UI-Panel)123-310 Send Queue Full (UI-Panel)123-311 Receive Queue
Full (UI-Panel)123-312 Diag mode change Fail (Punch unit type
set)123-317 Receive Message Queue Full (UI-Panel)123-318 Receive
Finish Queue Full (UI-Panel)123-320 NVM initialized for FCW
composition123-322 Target Fail (UI-Panel)123-323 Address Fail
(UI-Panel)123-325 Object Creation Fail (UI-Panel)123-326 Memory
Overflow (UI-Panel)123-327 Button Overflow (UI-Panel)123-328 UI
Internal Fail with Out of Area123-329 UI Internal Fail with Invalid
Coordinates123-332 I/F Fail (Invalid Parameter CP)123-333 I/F Fail
(Impossible Communication)123-337 Frame Data Error with Invalid
Data Type123-341 Event Queue Full (UI-Panel)123-342 Event Queue
Empty (UI-Panel)123-343 Invalid Class (UI-Panel)123-344 Invalid
Type (UI-Panel)123-345 Timer Queue Full (UI-Panel)123-346 Invalid
Timer Number (UI-Panel)123-350 One Touch Key Fail (MCW)123-352 Sys
EEPROM Read Error(UI-Panel)123-353 UI Cable Connect
Error(UI-Panel)123-354 Decrease in 24V Error(UI-Panel)123-355
Decreas in 5V Error(UI-Panel)123-356 FAX OTK Cable Connect
Error(UI-Panel)123-357 Sys EEPROM Write Error(UI-Panel)123-358 Log
EEPROM Write Error(UI-Panel) -
Code Description123-362 No Object (UI-Panel)123-368 Short of UI
Memory (UI-Panel)123-369 Invalid Interface Value (UI-Panel)123-370
Interface Length Fail (UI-Panel)123-371 Interface Parameter Fail
(UI-Panel)123-372 Interface Sequence Fail (UI-Panel)123-373 Channel
Fail (UI-Panel)123-374 Invalid User Job ID (UI-Panel)123-375
Internal Resource Fail (UI-Panel)123-376 Internal Memory Fail
(UI-Panel)123-377 UI Timer Fail (UI-Panel)123-378 Interface Format
Fail (UI-Panel)123-379 Dispatch Fail (UI-Panel)123-380 Copy
Interface Fail (UI-Panel)123-381 Fax Interface Fail
(UI-Panel)123-382 Scanner Interface Fail (UI-Panel)123-383 Report
Interface Fail (UI-Panel)123-384 Server Access Fail
(UI-Panel)123-385 Service Object Overflow (UI-Panel)123-386 Invalid
Service Object (UI-Panel)123-387 Invalid Service Object Attribute
(UI-Panel)123-388 Attribute Fail (UI-Panel)123-389 Argument Fail
(UI-Panel)123-390 Job Parameter Fail (UI-Panel)123-391 Job Actual
Parameter Fail (UI-Panel)123-392 Auditron Fail (UI-Panel)123-393 EP
Fail (UI-Panel)123-394 File Access Fail (UI-Panel)123-395 NVM Fail
(UI-Panel)123-396 FF Fail (UI-Panel)123-397 MGR Fail
(UI-Panel)123-398 Delay Release Queue Full (UI-Panel)123-399
Internal Fail (UI-Panel)123-400 JRM I/F Internal Fail
(UI-Panel)124-310 DC132 11124-311 DC132 09124-312 DC132 12124-313
DC132 10124-314 DC132 01124-315 DC132 02124-316 DC132 03124-317
DC132 04124-318 DC132 07124-319 DC132 08124-320 SEEPROM Fail124-321
Backup SRAM Fail124-322 DC132 05124-323 DC132 06124-324 All
Billings Mismatch -
Code Description124-325 Billing Restoration Fail124-326 IOT
Speed Not Registered124-327 IOT Speed Change SW Fail124-328 Punch
Unit User Initial SetUp124-331 ESS ROM DIMM #1 Not Found124-332
contract data mismatch124-333 ASIC Fail (Panther)124-334 Standard
Font ROM Error124-335 Font ROM Not Found124-337 ESS Standard RAM
Error124-338 Same Font ROMs Found124-339 ROM DIMM of Another
Product Found124-340 CRUM Market fail ALL124-341 CRUM Market fail
MCU124-342 CRUM Market fail SYS 1124-343 CRUM Market fail SYS
2124-344 All Billings Metertypes Mismatch124-345 Billing Meter Type
Restoration Fail124-346 All Billing CountTypes Mismatch124-347
Billing CountType Restoration Fail124-348 All Modal Break Points
Mismatch124-349 Modal Break Point Restoration Fail124-350 CRUM OEM
fail ALL124-351 CRUM OEM fail MCU124-352 CRUM OEM fail SYS 1124-353
CRUM OEM fail SYS 2124-360 CRUM validation fail ALL124-361 CRUM
validation fail MCU124-362 CRUM validation fail SYS 1124-363 CRUM
validation fail SYS 2124-372 IOT sc Soft Fail124-373 IOT Manager SW
Fail124-374 IOT IM DeviceDriver SW Fail124-380 CRUM Market fail ALL
(2)124-381 CRUM Market fail MCU (2)124-382 CRUM Market fail SYS 1
(2)124-383 CRUM Market fail SYS 2 (2)124-390 CRUM OEM fail ALL
(2)124-391 CRUM OEM fail MCU (2)124-392 CRUM OEM fail SYS 1
(2)124-393 CRUM OEM fail SYS 2 (2)124-700 Trimming Cancelled124-701
Output tray changed from Side Tray124-702 Output tray changed from
Stacker124-703 Booklet Tray to Center Tray124-704 Envelop Folder
Tray to Center Tra124-705 Punching Canceled124-706 Folding
Canceled124-708 Changed To Sub Tray -
Code Description124-709 Stapler sheets counts over
warning124-710 Output Tray changed from MailBoxSorter125-311
PSWcont Unexpected Fail127-210 DFE Communication Fail127-211 DFE
Parameter Error127-212 ExtPrint Check Mode Error127-213 ExtPrint
I/F Mismatch127-220 DEF Communicaiton Error (video)127-221 DEF
Communicaiton Error (Command)127-310 ESR Task Fatal error127-311
ExtPRTc Fatal Error127-312 DFE Video Link Fail127-313 ESS Video
Link Fail127-314 WSD Print S/W Fail127-315 ThinPrint S/W
Fail127-320 DFE Critical Fail127-337 JobTemplate HDD Write
Error127-342 JobTemplate Monitor Fail127-353 LPD Soft Fatal
error127-354 FTP Server Software Fail127-396 MailIO Soft Fatal
error127-398 IPP Soft Fatal error127-399 JME Soft Fatal
error127-700 SIP Registration Fail133-210 Fax Parameter
incorrect133-211 Fax Parameter Value Invalid133-212 Fax Read Erro
No Data133-213 Fax Read Error-Invalid Data133-214 Fax USB Open Fail
in Initializing133-215 Fax USB Device Fatal Error133-216 Fax USB
Host Fatal Error133-217 Fax Manager Short of Memory133-218 Fax Card
Message Library Short of Memory133-219 Fax Short of Work
Memory133-220 Fax Control task detects error133-221 Fax Card not
respond when system is Booting133-222 Fax Card does not respond
intervally133-223 Fax Card Reset133-224 Controller ROM Fax Card ROM
mismatch133-225 Fax address book illegal setting133-226 Illegal
country code for Fax133-280 Fax Option Slot1 Board Fail133-281
Received unknown message133-282 Fax Card download fail133-283 Fax
report mail box not open133-700 Staple/Punch Canceled133-710 Tray
select fail Used SMH instead134-210 Fax Cont Parameter
Invalid134-211 Fax Card Main Board Failure -
Code Description202-399 JME Soft Fatal error500-030 DC612 Print
NG By IOT Wait State500-990 DC612 Print NG By Any Reason